Programming Keygo Remote Controls - Fig. 23 And; Operating Test; Using Keytis Remote Controls - Fig; Obstacle Detection Function - Fig. 27 And - SOMFY Dexxo Pro io Manuel D'installation

Dexxo Pro io
cases:
modes.
control.
At this stage in the installation process, the Dexxo Pro motor drive unit
is ready to run.

4.7 Programming Keygo remote controls - Fig. 23 and

24
Each control button is programmed individually.
To clear a previously programmed button, refer to the section entitled "Clearing
Keygo remote controls".
- Programming from a Dexxo Pro motor.
- Programming by copying a previously programmed Keygo io remote
control.
> Programming from a Dexxo Pro motor (Fig. 23)
[1]. Press the "PROG
seconds).
[2]. Simultaneously press the outer right and outer left buttons on the remote
control.
[3].
> Programming by copying a previously programmed Keygo io
remote control (Fig. 24)
This operation is used to copy the programming of a previously programmed
remote control button.
[1]. Simultaneously press the outer right and outer left buttons on the
previously programmed remote control (A) until the green indicator light
comes on.
[2]. Press the button for 2 seconds to copy the previously programmed remote
control (A).
[3].
new remote control (B).
[4].
remote control (B).
At this stage in the installation process, the Dexxo Pro motor drive unit
is ready to run.

5 - OPERATING TEST

5.1 Using Keytis remote controls - Fig. 25

5.2 Using Keygo remote controls - Fig. 26

5.3 Obstacle detection function - Fig. 27 and 28

The detection of an obstacle during door opening will stop the door (Fig. 27).
The detection of an obstacle during door closure will reopen the door (Fig. 28).
Make sure that obstacle detection works when the door encounters an obstacle
50 mm from the ground.

5.4 Built in lighting operation

The light will come on every time the motor drive unit is operated. It will go
out automatically after one minute once the door stops. This time delay is
stay on continually may result in an automatic cut-off condition triggered by the
thermal cut out protection mechanism.

5.5 End-users training

The end-users must be imperatively instruct to the safety use of this motorised
door (standard use and manual release principle) as well as to periodic and
compulsery checks.
Copyright © 2015 Somfy SAS. All rights reserved

6 - CONNECTING PERIPHERALS

6.1 Description of the various peripherals - Fig. 29
Key. Description
1 Orange light
2
3 Code keypad
4 Keyswitch
5 Aerial
Battery
7 Pedestrian door safety kit
8 Photoelectric cells
10 Sensor bar
6.2 Electrical connections for the various peripherals -
Fig. 29 to 38
Cut the electric power supply to the motor before performing any work on
peripherals. If the display remains off after working on the system, check the
wiring (for possible short circuits or polarity reversals).
> General electrical diagram (Fig. 29)
> Photoelectric cells (Fig. 30)
It is compulsory to install photoelectric cells:
user)
A :
B :
This means that an automatic test is conducted to check photoelectric
cell operation every time the door operates.
If the test fails, no door movement is possible.
> Reflex photoelectric cell (Fig. 31)
"P2" = 1.
This means that an automatic test is conducted to check photoelectric cell
operation every time the door moves.
If the test fails, no door movement is possible.
> Sensor bar (Fig. 32)
"P2" = 1.
This is used to perform an automatic test of sensor bar operation every time
the door moves.
If the test result is negative, no door movement is possible.
account the photoelectric cells or the sensor bar.
> Orange light (Fig. 33)
Program the setting "P1
-
-
> Code keypad (Fig. 34)
> Pedestrian door safety kit (Fig. 35)
terminals 5 and 6.
> Battery (Fig. 36)
> Aerial (Fig. 37)
"P2" = 2.
"P2" = 1.
"P1" = 0.
"P1" = 1.
8