Maintenance, Care And Storage - Brill 41 B Mode D'emploi

Warning! Always switch
A
off the motor and wait
for the cutting tool to stop rotat-
ing before removing the grass
catcher.
To remove the grass catcher, move
the safety handle forwards over
the stop (Figure H) item 0, which
releases the folding handle.
Push the handle forwards to open
the multi-function box. Hold the
grass catcher by the handle with
one hand and remove (Figure J
item 11).
Note:
To ensure the grass catcher is filled
as full as possible, you should clean
the grass catcher and above all the
air grille after each use.

9. Maintenance, Care and Storage

9.1. Maintenance
Maintenance covers all work that
keeps your lawnmower in good
working order. You can prevent
accidents and failure of parts by
checking your lawnmower regularly
(check that the bolted connections
are secure, check for cracks
and damage) and by replacing
damaged or worn parts.
Repairs must only be carried out
by the service centres authorised by
the manufacturer or authorised
specialist dealers. A service centre
directory is supplied with your
lawnmower.
Warning! Always unplug
A
the spark plug connector
before carrying out all work and
repairs on your lawnmower.
Otherwise there is a risk of injury.
Check the grass catching device
regularly for wear or reduced
function. Replace defective
silencers. For safety reasons,
always replace worn or damaged
parts.
Never clean your lawnmower
under running water and in
particular never using a high-
pressure water jet due to the
danger of injury to people and
property.
Warning! Do not use your
A
hands or feet to remove
grass cuttings from the mower
housing. Use a suitable implement
such as a broom or dustpan brush.
To empty the grass catcher once
removed, hold it by the handle with
one hand and with the other hand
in the rear recess, tip the grass
cuttings out of the large opening
at the front.
Figure K
After emptying the grass catcher fit
it back into the holders provided
and tilt back the multi-function box.
Warning! The cutting tool
A
does not start rotating while
Store your lawnmower in a dry
place that is protected from frost.
Store your lawnmower out of the
reach of children.
Do not tip the motor onto the spark
plug side/carburettor side.
Observe the notes on installation
for exchanging the blade.
Maintenance on Wheel Drive
Figure M item 1
The gears run without maintenance
in a sealed oil bath. The wheel
drive clutch cable can be readjust-
ed if the clutch is acting too late or
is slipping. To adjust the cable, turn
the actuating wheel clockwise from
the operator's side. To ease it, turn
the actuating wheel anti-clockwise
from the operator's side.
9.2. Exchanging the Blade
Please only use original replace-
ments blades supplied by the
manufacturer. Original replacement
blades are available from your
specialist dealer.
Cutting path Original Brill
width replacement part
Article No.
41 cm 61601
43 cm 61600
48 cm 61602
51 cm 61603
the multi-function box is open.
Move the handle back to the work-
ing position and ensure it snaps
into place. Take care not to trap the
Bowden cables.
Warning! Only attach the
A
grass catcher when the
motor is switched off and the
cutting tool has stopped rotating.
Mowing without the Grass Catcher
The Brill brillencio lawnmower is
ideal for mowing long grass.
If you mow your lawn without the
grass catcher the grass cuttings are
distributed evenly over the lawn
from the high rear grass ejection
chute.
Never use replacement parts or
accessories not supplied by the
manufacturer.
If the cutter bar is damaged, it
must be replaced due to the
associated problems with
imbalance. For safety reasons,
the cutter bar must only be
replaced at the service centres
approved by the manufacturer
or by specialist dealers.
9.3. Maintenance Work on the
Motor
(Please read the notes provided by
the motor manufacturer. The origi-
nal operating instructions are sup-
plied with your lawnmower.)
Oil Change
Warning! Always change
A
the oil when the motor is
warm, the fuel tank is empty and
closed with the fuel cap.
Briggs & Stratton Motor and
Honda Motor
The oil must be changed for the
first time after 5 operating hours.
Additional oil changes are then
required every 50 operating hours.
If you do not operate your lawn-
mower for 50 hours within 1 year,
change the oil at the end of the
mowing season. To do this, open
GB
21