Display And Control Unit - Wayscral Everyway City 2021 Manuel D'instructions

II. Using your power-assisted bicycle
This power-assisted bicycle can be used with or without
assistance.
Once ac�vated, the electric assistance works a�er the pedals
are turned. The opera�ng principle is based on a cadence
sensor which, a�er detec�ng the pedals turning, ac�vates the
electric assistance. So, the slower the rota�on, the more
assistance is put in place.
However, please note that the assistance varies according to
the speed of the bicycle:
- it is high when star�ng,
- less high when the bicycle is in movement,
- then above 25 km/h, the assistance cuts out. It will
automa�cally resume when the speed is lower. You can
go faster, but you will have to do it on your own, without
any power assistance.
a)

Display and control unit

No. Element
1 Display
2 Stop/Start
bu�on
3
Bu�on
4
Mode Bu�on
5
Bu�on v
6 Pedestrian
Bu�on
7 USB port
To ac�vate the assistance:
- Press once on the bu�on at the top of the ba�ery then
- Press and hold the start/stop bu�on
seconds)
To deac�vate it:
- press and hold the bu�on
- press and hold the bu�on at the bo�om of the ba�ery for a
few seconds.
When the ba�ery is turned off, it no longer supplies power to
your bicycle's motor. A�er a certain period of inac�vity, the
display is switched off to save energy.
To reset the display of the kilometre counter, press and hold
the Mode bu�on a�er turning on the display. The "Trip" logo
will flash.
Press the Mode bu�on.
Use the or v bu�ons to make your choice and press the
Mode bu�on to confirm.
Press and hold the M bu�on to save your choices and exit the
se�ng mode.
In the event of a fault, the symbol
Various error codes are also displayed.
Func�on
View assistance informa�on
Stop/Start the
display/assistance
Increase
Short press: select the
informa�on to display
Long press: choose se�ngs
Decrease
Ac�vate Pedestrian Mode
Charge your mobile devices
on the display (3
on the display (3 seconds) and
indicates a failure.
When an error code is displayed, first restart the system
following the solu�on suggested in the table below.
If the problem persists or if another code appears, please
contact your retailer.
Code Problem
21 Power supply
problem
22 Problem with the
accelerator, if
installed
23 Motor phase wire
failure
24
Hall effect sensor
cable failure
25 Problem with
brakes
30
Communica�on
error
b) Symbols and indicators
The display includes the following elements.
Briefly press the Mode bu�on to scroll through the usage data.
Some components are not used on this model of bicycle.
No. Descrip�on
1 Ligh�ng ac�va�on
2 Usage data / Errors
TRIP: daily kilometres
ODO: total number of kilometres
: failure detected
21-30: error code
3 Speed and speed units
AVG: average speed
MAX: maximum speed
Pedestrian Mode
4 Assistance level selected
5 Ba�ery level
Indicator
Flashing red indicator light
Red indicator light
Green indicator light
Blue indicator light
17/80
Solu�on
There is a problem with
the circuit regulator.
Contact your retailer.
Check the accelerator. If
the problem persists,
contact your retailer.
Check the state of the
motor. If the problem
persists, contact your
retailer.
Check the state of the
motor. If the problem
persists, contact your
retailer.
Check your brakes. If
the problem persists,
contact your retailer.
Check that the
connec�ons in the
controller are correct. If
the problem persists,
contact your retailer.
Charge level
0% to 10%
11% to 30%
31% to 70%
71% to 100%