Technical Data; Before Operation - Scheppach dp13 Traduction Du Manuel D'origine

GB
18. Check the tool for damage
Before using the tool, safety devices and
any slightly damaged parts must be carefully
checked to ensure that they are in good working
order. Visually examine the tool's power cable on
a regular basis. All parts must be correctly as-
sembled and meet all the conditions required to
ensure proper operation.
19. Unless otherwise specified in the operating in-
structions, any damaged safety devices and
parts must be properly repaired or replaced by a
professionally recognized workshop. Never use
tools with defective On/Off switches.
20. Warning! Using any plug-in tools and accesso-
ries other than those specified in these operating
instructions can lead to injury.
21. Maximum workpiece size
Workpieces (max. 20 x 20 cm) may only be pro-
cessed if they can be clamped securely on the
drill table or in the vise.
Remaining hazards
The machine has been built using modern tech-
nology in accordance with recognized safety
rules. Some remaining hazards, however, may
still exist.
• Long hair and loose clothing can be hazardous
when the work piece is rotating. Wear personal
protective gear such as a hair net and tight fitting
work cothes.
• Wood chips and saw dust can be health hazard.
Be sure to wear personal protective gear such as
safety goggles and a dust mask. Use a vacuum
exhaust system.
• Thrown work pieces can lead to injury if the work
piece is not properly secured or fed, such as work-
ing without a limit stop.
• The use of incorrect or damaged mains cables can
lead to injuries caused by electricity.
• Even when all safety measures are taken, some
remaining hazards which are not yet evident may
still be present.
• Remaining hazards can be minimised by follow-
ing the instructions in „safety precautions", „proper
use" and in the entire operating manual.
Keep this safety information in a safe place.
22 / 152
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

6. Technical data

Dimensions L x B x H mm
Chuck size mm
Spindle cone seat
Drilling chuck cone seat
Drilling chuck clamping range mm
Spindle rise and fall range mm
Chuck to worktable mm
Spindle base working range mm
ø Column mm
Weightt kg
Drive
Rated voltage V/Hz
Power rating
Speeds 1/min
Subject to technical modifications!
Load factor:
Operating mode S2 15 min (short-time duty) means
that you may operate the motor continuously at its
nominal power level (350 W) for no longer than 15
minutes ON period. If you fail to observe this time limit
the motor will overheat. During the OFF period the
motor will cool again to its starting temperature.
Noise
Sound values were measured in accordance with
EN 61029.
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
WA
Uncertainty K
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Limit the noise to a minimum!
• Only use appliances which are in perfect working
order.
• Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever neces-
sary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
7.

Before operation

WARNING:
For your own safety never connect plug to power
source outlet until all assembly steps are completed
and you have read and understood the safety and
operational instructions
430x200x580
13
B16
B16
1,5 - 13
50
138
215
46
14,4
230/50
350W S2
15min
600 / 900 /
1200 /
1750 / 2600
70,7 dB(A)
3 dB
86 dB(A)
3 dB