Technical Data; Before Commissioning; Installation - Scheppach DP19Vario Instructions D'origine

• Avoid accidental starting of the machine: the oper-
ating button may not be pressed when inserting the
plug in an outlet.
• Use the tool that is recommended in this manual. In
doing so, your saw provides optimal performance.
• Hands may never enter the processing zone when
the machine is in operation. Release the handle
button and switch off the machine prior to any op-
erations.
• Prior to any adjustment, maintenance or service
work disconnect the mains power plug!

6. Technical Data

Nominal input voltage
Power rating
Motor speed
Output speed (infinitely
adjustable)
Drill chuck mount
Chuck
Dimensions of drill table
Angle adjustment
Drilling depth
Pillar diameter
Height
Weight
Laser class
Wavelength of laser
Laser output
Noise and vibration values
The noise levels have been determined in accord-
ance with EN 61029.
sound pressure level - no load L
sound pressure level - load L
uncertainty K
pA
sound power level - no load L
sound power level - load L
WA
uncertainty K
WA
Wear hearing protection.
Excessive noise can result in a loss of hearing. To-
tal vibration values (vector sum of three directions)
determined according to EN 61029.
Vibration emission value a = 1.7 m/s
h
K uncertainty = 1,5 m/s
2
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
230-240V~ 50 Hz
550 W
1450 min
-1
440 - 2580 min
-1
B16
1 - 16 mm
198 x194 mm
45° - 0° - 45°
60 mm
60 mm
830 mm
27,5 kg
2
650 mm
1mW
70.2 dB(A)
pA
73.5 dB(A)
pA
3 dB(A)
82.7 dB(A)
WA
86.3 dB(A)
3 dB(A)
2
The specified vibration value was established in ac-
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the specified value in excep-
tional circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.

7. Before commissioning

• Open the packaging and carefully remove the de-
vice.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and the packaging are not children's
toys! Do not let children play with plastic bags,
films or small parts! There is a danger of chok-
ing or suffocating!

8. Installation

Column and machine foot, fig. 3
1. Set the machine foot (1) down on the ground or
the workbench.
2. Place the column (2) on the base plate so that the
holes on the column (2) align with the holes on the
base plate (1).
3. Screw the four hexagonal screws (17) to fasten
the column into the base plate and tighten them
using a hexagon spanner.
Removing the rack, Fig. 4
In order to install your drill, you must first remove the
rack (D)
1. Use an Allen key (SW3) to remove the ring (E) and
pull this off the column (2).
2. Now pull the rack (D) out.
Installing the drilling table holder, Fig. 5-7
1. Insert the rack (D) into the groove on the drilling
table holder (4).
2. Align the rack (D) centrally in relation to the drilling
table holder (4).
3. When bringing the rack (D) together within the
groove, ensure that the tooth meshing between
the rack and the drilling table holder (4) is correct.
GB | 27