Chicco Seat 4 Fix Mode D'emploi page 30

equipped with rear vehicle seat belt with in-
tegrated air bags (inflatable seat belts), follow
the car manufacturer's instruction manual.
2. INSTALLATION
WARNING! The text and figures of these
instructions are for the installation of the
child car seat on the back right seat.To fit
the child car seat in other positions, carry
out these operations in the same order.
2.1 HOW TO FIT THE CHILD CAR SEAT
(with ISOFIX SYSTEM) REAR-FACING:
GR. 0+ (0-13 KG) and GR1 (9-18 KG)
For the Group 0+ configuration, the Car Seat
must ALWAYS be rear-facing, with the airbag
Deactivated.
Installation must ALWAYS be carried out using
the Isofix connectors and Top Tether
• Use the recline lever (P), to line up the red dot
with position R (Fig. 5)
• Use the lever (Q) to rotate the seat 180°, veri-
fying that it has locked in the rear-facing po-
sition (Fig. 6).
• Position the Car Seat on the seat of the vehi-
cle in the rear-facing direction.
• Pull out the rigid connectors (C) completely,
pulling the tape outwards (V) (Fig. 7).
• To make it easier to fasten the Isofix connec-
tors, it is possible to use the special guides
provided, attaching them to the Isofix hooks
of the car (Fig. 8)
• Fasten the connectors to the hooks present
between the backrest and the seat (Fig. 9).
Once fastening occurs, you will hear a typical
"click" and the indicator will change from red
to green.
• Firmly push the Car Seat toward the backrest
of the vehicle seat to ensure the best fit (Fig.
10).
• Remove the Top Tether (F) from the door (W)
(Fig. 11).
• Extend the Top Tether strap by pressing the
adjustment button (Y).
• Pass the Top Tether through the blue belt
guide (Fig. 12).
WARNING! Pass the Top Tether between the
top of the car seat backrest and the headrest.
Never pass the Top Tether above the car head-
rest.
WARNING! Refer to your car's user manual to
identify where the Top Tether of the child car
seat is attached to the car. This fastening point
is denoted with a specific label (Fig. 13) and
can be found in the positions indicated by the
figures 13A – 13B – 13C – 13D.
WARNING! Check that the Top Tether fastener
used is the one that has been specially desig-
nated. Do not confuse it with a ring used for
hanging bags (Fig. 14).
• Once you have identified the fastening point,
connect the Top Tether hook (X) to it.
Adjust the length of the Top Tether belt by
forcefully pulling the belt until it is tight. The
indicator on the belt goes green (Z) when the
tether is suitably tight (Fig. 15). Roll up any ex-
cess belt and tie up using the velcro.
The booster cushion including the pad and
headrest is to be used from birth up to 6 kg.
Refer to paragraph 3.1 BOOSTER CUSHION
To disassemble the child car seat, unhook the
Top Tether and the Isofix connectors by press-
ing the release buttons (D) (Fig. 16). To put
them back in completely push them inwards.
Once installation is complete place the baby in
the seat as follows:
• Rotate the seat of the car child seat (90°) us-
ing the lever (Q) until it is positioned facing
you, to make it easier to place the child.
• Press the belt adjustment button (S) and hold
and pull both the Child Car Seat belts toward
yourself until the maximum length is reached
(Fig. 17).
• Unbuckle the Car Seat belts by pressing the
button on the buckle (Fig. 18).
• Place the baby in the car seat with care, join
the two buckle tongues and fasten them in
the buckle again (Fig. 19).
• To adjust belt tightness, pull the adjustment
strap (R) upwards with caution until the belt
is suitably tight (Fig. 20).
• Turn the seat rear-facing.
30