Packing List - Homelite HCS3335A Manuel D'utilisation

GB
F D E I P
ASSEMBLY
WARNING:
If any parts are damaged or missing do not
operate this product until the parts are replaced.
Failure to heed this warning could result in
serious personal injury. This product has been
shipped completely assembled.
WARNING:
Do not attempt to modify this product or create
accessories not recommended for use with this
product. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
NOTE: The chainsaw has been fully factory
tested. It is normal to find some slight lubricant
residue on the saw. Read and remove all hang
tags and store with the Operator's Manual.
WARNING:
Before first use, it is essential that you follow the
'Chain Adjustment' guide (following this section)
to ensure the bar and chain have not become
loose in transit. Never operate a chainsaw with
incorrectly adjusted chains. Failure to follow these
steps could result in severe personal injury.
UNPACKING
Carefully remove the product and any accessories
■
from the box. Make sure that all items listed in the
packing list are included.
Inspect the product carefully to make sure no
■
breakage or damage occurred during shipping.
Do not discard the packing material until you have
■
carefully inspected and satisfactorily operated the
product.
If any parts are damaged or missing, please call your
■
Homelite service centre for assistance.

PACKING LIST

Chainsaw
Scabbard
Combination Wrench
2-Cycle Engine Lubricant
Case (HCS3840CA / HCS4245CA )
Operator's Manual
HCS3435A-25lgs manual.indd Sec1:34 HCS3435A-25lgs manual.indd Sec1:34
NL S DK N FIN GR HU
English
ADJUSTING THE CHAIN TENSION (TOOL-
LESS CHAIN TENSIONING)
See Figures 2-3, 37, 42-45.
■
■
■
■
■
■
■
Note: If chain is too tight, it will not rotate. Loosen the
clutch cover lock knob by pressing in and slightly rotating
counter clockwise, then rotate the chain tensioning dial
counter clockwise. Lift the tip of the guide bar up and
retighten the clutch cover lock knob securely. Ensure that
the chain will rotate without binding.
34
CZ RU RO PL SLO HR TR EST LT
WARNING:
Never touch or adjust the chain while the
motor is running. The saw chain is very sharp.
Always wear protective gloves when performing
maintenance on the chain.
Stop the engine before setting the chain tension.
Slightly loosen the clutch cover lock knob by pressing
in and rotating counter clockwise. (Figures 37)
Turn the chain tensioning dial clockwise to tension the
chain. (Figures 44)
Note: A cold chain is correctly tensioned when there
is no slack on the underside of the guide bar, the
chain is snug, and it can be turned by hand without
binding.
Re-tension the chain whenever the flats on the drive
links hang out of the bar groove. (Figures 3)
Note: During normal saw operation, the temperature
of the chain increases. The drive links of a correctly
tensioned warm chain will hang approximately 1.2mm
out of the bar groove. The tip of the combination
wrench can be used as a guide to help determine the
correct warm chain tension.
Note: New chains tend to stretch; check the chain
tension frequently and tension as required.This is the
same for a NEW tool.
Lift the tip of the guide bar up to check for sag.
(Figures 43)
Release the tip of the guide bar and turn the chain
tensioning dial clockwise. Repeat this process until
sag does not exist.
Hold the tip of the guide bar up and tighten the
clutch cover lock knob securely. The chain is correctly
tensioned when there is no sag on the underside of
the guide bar, the chain is snug, but it can be turned
by hand without binding. Ensure that the chain brake
is not set.
LV SK BG
12/19/08 3:08:47 PM 12/19/08 3:08:47 PM