Faults And Repair; Technical Data; Noise/Vibration Information - Batavia MAXXPACK BT-CCS004 Mode D'emploi

English
Protect the product against impact and
4.
intense vibrations, which occur particu-
larly when transporting in vehicles.
Secure the product against shifting and
5.
tilting.

10. Faults and repair

WARNING!
Only carry out work that is
described in this user manual! Any
other inspection, maintenance or repair
work must be carried out by authorised
After Sales Support or a similarly qualified
professional!
Alleged malfunctions, faults or damage are
often caused by situations that could have
been rectified by the user themselves.
Therefore, check the product before con-
tacting a professional by using the table
below. In most cases, faults can be reme-
died quickly.

11. Technical data

Nominal voltage/frequency: . . . . . . 18 V~
Protection class: . . . . . . . . . . . . . . . .III
Idle speed n /rated speed n: . . . 3150 min
0
Cutting depth: . . . . . . . . . . .
Weight: . . . . . . . . . . . . . approx. 1.7 kg
TCT saw blade
Dimensions: . . . . . . Ø 89 × Ø 10 × 1.8 mm
Number of teeth/segments: . . . . . . . 24 T
Material:. . . . . . . . . . . . . . . . . . Wood
Max. speed permitted: . . . n
HSS saw blade
Dimensions: . . . . . . Ø 89 × Ø 10 × 1.6 mm
Number of teeth/segments: . . . . . . . 44 T
Material:. . . . . . . . . . . . . Wood, plastic
Max. speed permitted: . . . n
Diamond cutting disc
Dimensions: . . . . . . Ø 89 × Ø 10 × 1.7 mm
Material:. . . . Tile, marble, granite, concrete
Max. speed permitted: . . . . . .17100 min
Top operating speed: . . . . . . . . . 80 m/s
Laser
Class: . . . . . . . . . . . . . . . . . . . . . . 2
Standard: . . . . . . . . . . EN 60825-1:2014
Wavelength λ: . . . . . . . . . . . . . 650 nm
20
Output energy P
Battery: . . . . . . . . 2 × 1.5 V⎓, Li-Ion, LR44

12. Noise/vibration information

Attention!
The vibration level will change according to
the use of the power tool and can be above
the value stated in these instructions in
some cases.
The vibration load may be underestimated if
the power tool is used in this way on a regu-
lar basis. Attempt to keep the stress associ-
ated with vibrations as small as possible.
Exemplary measures that can reduce vibra-
tion stress include wearing gloves when
using the tool and limiting the amount of
time you use it. At the same time, all parts
of the operating cycle must be accounted
for (e.g. times when the power tool is turned
off and when it is turned on, but not operat-
ing under load).
The vibration level stated in these instruc-
tions was measured according to an EN
-1
62841 standard measurement method and
. 28 mm
can be used for comparing equipment. The
max
specified vibration emission level may also
be used to initially assess the exposure.
Noise level determined in accordance with
EN 62841. The A-weighted noise level of the
power tool normally amounts to:
Noise emission
10000 min
-1
max
Sound pressure level L
Sound power level L
Uncertainty K: . . . . . . . . . . . . . 3 dB(A)
Vibration values
When cutting wood . . . . . . . . . 4.78 m/s
10000 min
-1
max
Uncertainty K: . . . . . . . . . . . . .1.5 m/s
When cutting metal . . . . . . . . . 3.95 m/s
Uncertainty K: . . . . . . . . . . . . .1.5 m/s
Vibration and noise reduction
-1
Limit the operation time, use low vibration
and quiet operating modes and wear per-
sonal protective equipment to reduce vibra-
tion and noise impact.
The following measures help to reduce risks
caused by vibration noise:
: . . . . . . . . . . . ≤ 1 mW
0
WARNING!
Wear ear protection!
: . . . . . . 85 dB(A)
pA
: . . . . . . . 96 dB(A)
WA
2
2
2
2