Publicité
e9/e6
/e6 headboard bracket installation guide (optional)
+
For Series e9/e6+/e6 only. See page 19 for e4 optional Headboard Bracket installation.
A 9/16" (14 mm) & 1/2" (13 mm) socket and crescent wrench are necessary to complete installation.
HEADBOARD BRACKET COMPONENTS
Headboard Bracket (2)
T-Bracket (2)
STEP 1
a.) Align the hole in the bracket to the brass sleeve into
which the leg threads. Hold the bracket in place and
screw the leg into the base until it is snug. DO NOT
OVERTIGHTEN. Too much force may cause the leg
to spin freely.
b) Align the tab with the hole in the frame (located
towards the foot of the base) and use a short bolt
and nut to secure the bracket. Make sure the bolt is
tight.
STEP 3
You may now connect your headboard to the attachment plates using the remaining short bolts and nuts to
secure it to the brackets. The heads of the bolts will face outward. Use a 9/16" (14mm) socket and 1/2" (13mm)
wrench to tighten the bolts.
18
Spacer (2)
Long Bolt (8)
Short Bolt (10)
Nut (18)
STEP 2
Attach the plastic spacer and T-Bracket.
a.) Measure the distance between the mounting
holes on the headboard and install the spacer and
attachment plate to accommodate the headboard.
b.) To install the plastic spacer and attachment plate,
you will need (2) long bolts and (2) nuts. Place the
spacer and attachment plate in the desired location
and slip the bolts through the holes with the head
of the bolt facing outward. Position the bolts
diagonally on the spacer. Use the 9/16" (14 mm)
socket and wrench to tighten the bolts.
e4+/e4 headboard bracket installation guide (optional)
For Series e4+/e4 only. See page 18 for e9, e6+, e6 and e4+ Headboard Bracket installation.
The e4+/e4 Headboard Brackets are an optional accessory and are not included.
A 9/16" (14 mm) & 1/2" (13 mm) socket and crescent wrench are necessary to complete installation.
HEADBOARD BRACKET COMPONENTS
Headboard Bracket (2)
T-Bracket (2)
STEP 1
a.) Align the hole in the bracket to the brass sleeve into
which the leg threads. Hold the bracket in place and
screw the leg into the base until it is snug. DO NOT
OVERTIGHTEN. Too much force may cause the leg
to spin freely.
b) The headboard bracket will have 2 tabs to
accomodate any frame type. Align the appropriate
tab on the bracket with the hole on the base. Use a
short bolt and nut to secure the bracket. Make sure
the bolt is tight.
STEP 3
You may now connect your headboard to the attachment plates using the remaining short bolts and nuts to
secure it to the brackets. The heads of the bolts will face outward. Use a 9/16" (14mm) socket and 1/2" (13mm)
wrench to tighten the bolts.
Spacer (2)
Long Bolt (8)
Short Bolt (10)
Nut (18)
STEP 2
Attach the plastic spacer and T-Bracket.
a.) Measure the distance between the mounting
holes on the headboard and install the spacer and
attachment plate to accommodate the headboard.
b.) To install the plastic spacer and attachment plate,
you will need (2) long bolts and (2) nuts. Place the
spacer and attachment plate in the desired location
and slip the bolts through the holes with the head
of the bolt facing outward. Position the bolts
diagonally on the spacer. Use the 9/16" (14 mm)
socket and wrench to tighten the bolts.
19
Publicité
