Programming Your Safe - SentrySafe QAP1BE Manuel Du Propriétaire

Programming Your Safe

NOTE: Store code and keys in a secure location (other than in the safe).
NOTE: SentrySafe offers a secure on-line location for the entry and retrieval of your code.
Go to www.registermysafe.com and register your safe.
Preparing your safe for first-time use
Insert key into keyhole and turn clockwise.
A
NOTE: Do not lock key inside safe – this is an override key and will
open the safe in the event that you have lost your code.
Programming your safe
Remove the battery pack cover.
A
Pull out battery pack (keep battery pack connected
B
to wires).
Insert four NEW AA alkaline batteries.
C
NOTE: Do not use rechargeable batteries or any other type of non-alkaline battery.
Do not mix old and new batteries. Do not mix alkaline and standard batteries.
IMPORTANT
All safe models initially work with the factory code 1, 2, 3, 4, 1. It is therefore
important to re-program your safe with a new user code you have personally
selected to provide maximum security.
The Quick Access Pistol Safe comes with a built-in code.
Factory code 1, 2, 3, 4, 1.
1 2 3 4
Press any button once to bring the safe out of standby mode, then
enter the Factory Code 1, 2, 3, 4, 1.
The Green LED will light.
To Program an Electronic Code
Find the Reset button located behind the battery pack.
A
Press and hold the Reset button until the keypad flashes 3 times.
B
The LEDs remain on to indicate it is ready to accept a new user code.
Enter a user code that is four, five or six digits long.
C
A successful programming of the user code is indicated when the
D
LED light flashes green three times.
4
Programming Your Safe
To Change an Electronic Code
Press and hold the Reset button until the keypad flashes 3 times.
A
Enter a new user code that is four, five or six digits long. The safe
B
will then automatically erase the previous user code.
NOTE: Write down your user code, and keep it in a secure location.
Or visit www.registermysafe.com to store your user code.
–OR–
To Program Primary User Fingerprints on Models
with Biometric Lock
(Up to four fingerprints can be programmed)
Press and hold the Reset button until the keypad flashes 3 times.
A
The LEDs will remain on to indicate that the safe is ready to
accept two new fingerprints.
Swipe the first finger across the fingerprint scanner multiple
B
times. The LED light will flash green once for each valid scan.
When enough valid scans have been recorded (usually 5-10
C
scans), there will be a brief pause and the LED light will flash
green 3 times to indicate successful programming.
Immediately add a second fingerprint following the registration
D
of the previous one. Repeat steps B and C as indicated above.
To Program Secondary User Fingerprints
Press and hold the Reset button until the keypad flashes 3 times. Once the LEDs remain
A
on, press and hold the Reset button again until the LEDs flash. The LEDs will remain on to
indicate that the safe is ready to accept two new fingerprints.
Repeat steps B, C and D as indicated under: To Program Primary User Fingerprints
B
To Erase Fingerprints
Press and hold the Reset button until the keypad flashes 3 times. The LEDs remain on to
A
indicate the safe is ready to erase fingerprints.
Swipe a programmed fingerprint once and wait 10 seconds. The red LED will flash 3 times to
B
indicate all programmed fingerprints have been erased.
NOTE:
- The user code or fingerprint programmed will not be erased when the battery power is removed.
- If you program a four or five digit user code, then you will need to wait 10 seconds until your
code is accepted. This is only valid during the setup of your safe. If you program a six digit user
code, then the light will immediately turn green.
- If the red LED flashes 3 times, programming failed.
- When you are finished programming your safe, replace the battery pack cover.
5