Manufacturer's Warranty; Spare Parts Lists - REMS eva 1/8 - 2 Notice D'utilisation

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 9
eng
5. Faults
5.1. Fault: Die stock has diffi culty cutting.
Cause:
● Not original REMS die heads.
● REMS dies are blunt.
● Unsuitable or insuffi cient thread cutting material
5.2. Fault: No workable thread, thread rips off.
Cause:
● REMS dies are blunt.
● REMS dies inserted incorrectly.
● Unsuitable or insuffi cient thread cutting material
● Pipe material is unsuitable for thread cutting.
5.3. Fault: Thread is cut skew to the pipe axis.
Cause:
● Pipe not cut at right angle
5.4. Fault: Pipe slips in the vice.
Cause:
● Pipe not clamped tight enough.
● Vice/die unsuitable or defective.
6. Disposal
The tool may not be thrown into the domestic waste at the end of use. It must
be disposed of properly by law.

7. Manufacturer's Warranty

The warranty period shall be 12 months from delivery of the new product to the
fi rst user. The date of delivery shall be documented by the submission of the
original purchase documents, which must include the date of purchase and the
designation of the product. All functional defects occurring within the warranty
period, which are clearly the consequence of defects in production or materials,
will be remedied free of charge. The remedy of defects shall not extend or
renew the warranty period for the product. Damage attributable to natural wear
and tear, incorrect treatment or misuse, failure to observe the operational
instructions, unsuitable operating materials, excessive demand, use for unau-
thorized purposes, interventions by the customer or a third party or other
reasons, for which REMS is not responsible, shall be excluded from the warranty
Services under the warranty may only be provided by customer service stations
authorized for this purpose by REMS. Complaints will only be accepted if the
product is returned to a customer service station authorized by REMS without
prior interference and in a fully assembled condition. Replaced products and
parts shall become the property of REMS.
8
Remedy:
● Only use REMS quick-change die heads, REMS quick-change die heads S,
REMS plug-on heads for button dies.
● Change REMS dies, see 4.2.
● Use suffi cient, undiluted quantity of REMS Spezial or REMS Sanitol thread
cutting material
Remedy:
● Change REMS dies, see 4.2.
● Note the numbering of the REMS dies to the slot number of the die head body
(10), see 4.2, change REMS dies if necessary
● Use suffi cient, undiluted quantity of REMS Spezial or REMS Sanitol thread
cutting material
● Only use approved pipes.
Remedy:
● Cut pipe at right angle with REMS Tiger with guide holder and REMS special
saw blade or with REMS RAS St, REMS Turbo K, REMS Cento
Remedy:
● Increase clamping pressure.
● Change vice/die. REMS Aquila 3B/REMS Aquila WB
is recommended for secure clamping.
The user shall be responsible for the cost of shipping and returning the product.
A list of the REMS-authorized customer service stations is available on the
Internet under www.rems.de. For countries which are not listed, the product
must be sent to the SERVICE-CENTER, Neue Rommelshauser Strasse 4,
71332 Waiblingen, Deutschland. The legal rights of the user, in particular the
right to make claims against the seller in case of defects as well as claims due
to wilful violation of obligations and claims under the product liability law are
not restricted by this warranty.
This warranty is subject to German law with the exclusion of the confl ict of laws
rules of German International Private Law as well as with the exclusion of the
United Nations Convention on Contracts for the International Sales of Goods
(CISG). Warrantor of this world-wide valid manufacturer's warranty is REMS
GmbH & Co KG, Stuttgarter Str. 83, 71332 Waiblingen, Deutschland.

8. Spare parts lists

For spare parts lists, see www.rems.de → Downloads → Parts lists.
eng

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Eva 1/8 - 2''Eva 1/8

Table des Matières