Manufacturer's Warranty; Spare Parts Lists - REMS Mini-Cobra A Notice D'utilisation

eng
Pull the pipe cleaning spiral about 300 mm out of the spiral drum (10), tighten
the chuck (5) by hand. Always start the electric drill screwdriver at low speed
in right right hand rotation and increase the speed as required. Only insert the
pipe cleaning spiral into the pipe to an extent that the chuck (5) can still be
operated by hand. Switch off the electric drill/screwdriver. Open the chuck (5)
and pull the pipe cleaning spiral about 300 mm back out of the spiral drum (10).
Repeat the process until you can feel a resistance or the blockage is cleared.
Keep a maximum distance of 200 mm between the end of the pipe/drain and
the chuck (5) otherwise the pipe cleaning spiral can loop. Always pull back the
pipe cleaning spiral by hand and push it back into the spiral drum. Only use
anticlockwise rotation of the electric drill/screwdriver if the pipe cleaning spiral
is jammed in the pipe. Switch the electric drill/screwdriver carefully between
clockwise and anticlockwise rotation to remedy this.
4. Maintenance
Notwithstanding the maintenance described below, it is recommended to send
in the electric pipe cleaning machine to an authorised REMS contract customer
service workshop for inspection and periodic testing of electrical devices at
least once a year. In Germany, such periodic testing of electrical devices should
be performed in accordance with DIN VDE 0701-0702 and also prescribed for
mobile electrical equipment according to the accident prevention rules DGUV,
regulation 3 "Electrical Systems and Equipment". In addition, the respective
national safety provisions, rules and regulations valid for the application site
must be considered and observed.
5. Faults
REMS Mini-Cobra A
5.1. Fault: Electric pipe cleaning machine does not start.
Cause:
● Worn carbon brushes.
● Mains lead defective.
● Electric pipe cleaning machine defective.
5.2. Fault: No feed of the pipe cleaning spiral.
Cause:
● Thrust handle (1) was not engaged.
● Pipe cleaning spiral stuck in the pipe or in a pipe blockage.
● Pipe cleaning spiral is not mounted in the spiral drum (10) in clockwise
direction.
● Electric pipe cleaning machine defective.
6. Disposal
REMS Mini-Cobra A may not be thrown in the domestic waste after use. It must
be disposed of properly by law.

7. Manufacturer's Warranty

The warranty period shall be 12 months from delivery of the new product to the
fi rst user. The date of delivery shall be documented by the submission of the
original purchase documents, which must include the date of purchase and the
designation of the product. All functional defects occurring within the warranty
period, which are clearly the consequence of defects in production or materials,
will be remedied free of charge. The remedy of defects shall not extend or
renew the warranty period for the product. Damage attributable to natural wear
and tear, incorrect treatment or misuse, failure to observe the operational
instructions, unsuitable operating materials, excessive demand, use for unau-
thorized purposes, interventions by the customer or a third party or other
reasons, for which REMS is not responsible, shall be excluded from the warranty
Services under the warranty may only be provided by customer service stations
authorized for this purpose by REMS. Complaints will only be accepted if the
product is returned to a customer service station authorized by REMS without
prior interference and in a fully assembled condition. Replaced products and
parts shall become the property of REMS.
4.1. Maintenance
WARNING WARNING
Pull out the mains plug before maintenance work!
Clean the electric pipe cleaning machine and the pipe cleaning spiral regularly
especially when they have not been in use for a long time. Clean plastic parts
(e.g. housing) only with REMS CleanM machine cleaner (Art. No. 140119) or
a mild soap and a damp cloth. Do not use household cleaners. These often
contain chemicals which can damage the plastic parts. Never use petrol,
turpentine, thinner or similar products for cleaning.
Make sure that liquids never get onto or inside the electric pipe cleaning machine.
Never immerse the electric pipe cleaning machine in liquid.
4.2. Inspection/Repair
REMS Mini-Cobra A
WARNING WARNING
Pull out the mains plug before maintenance and repair work! This work
may only be performed by qualifi ed personnel.
The gear runs in a life-long grease fi lling and therefore needs no lubrication.
The drive machine motor has carbon brushes. These are subject to wear and
must therefore by checked and changed by qualifi ed specialists or an author-
ised REMS customer service workshop from time to time.
Remedy:
● Have carbon brushes changed by qualifi ed technical personnel or an
authorised REMS customer service workshop.
● Have the connecting cable changed by qualifi ed technical personnel or an
authorised REMS customer service workshop.
● Have the electric pipe cleaning machine inspected/repaired by an authorised
REMS customer service workshop.
Remedy:
● Engage thrust handle (1), see 3.1. Operation REMS Mini-Cobra A.
● Switch off the electric pipe cleaning machine. Set the direction of rotation
switch (3) to the arrow in the direction of the switch handle (2). Press the safety
inching switch (4) lightly so that the spiral drum (10) turns, then increase the
speed slowly as required.
● Remove pipe cleaning spiral and re-mount, see 2.2.
● Have the electric pipe cleaning machine inspected/repaired by an authorised
REMS customer service workshop.
The user shall be responsible for the cost of shipping and returning the product.
A list of the REMS-authorized customer service stations is available on the
Internet under www.rems.de. For countries which are not listed, the product
must be sent to the SERVICE-CENTER, Neue Rommelshauser Strasse 4,
71332 Waiblingen, Deutschland. The legal rights of the user, in particular the
right to make claims against the seller in case of defects as well as claims due
to wilful violation of obligations and claims under the product liability law are
not restricted by this warranty.
This warranty is subject to German law with the exclusion of the confl ict of laws
rules of German International Private Law as well as with the exclusion of the
United Nations Convention on Contracts for the International Sales of Goods
(CISG). Warrantor of this world-wide valid manufacturer's warranty is REMS
GmbH & Co KG, Stuttgarter Str. 83, 71332 Waiblingen, Deutschland.

8. Spare parts lists

For spare parts lists, see www.rems.de → Downloads → Parts lists.
eng
9