Important Safety Instructions; Fcc And Ic Regulations - Angelcare AC115 Manuel Du Propriétaire

26. Remove batteries from units if you store the product over 30 days
because the batteries could leak and damage the product.
27. Discard 'dead' batteries as soon as possible since 'dead' batteries are more
likely to leak in a product. If a battery has leaked or vented, discard product
responsibly.
28. DO NOT store this product, or the batteries provided with or identified for
use with this product, in high-temperature & high humidity environments and
avoid direct sunlight.
IMPORTANT SAFETY
INSTRUCTIONS
29. This monitor uses public airwaves to transmit signals. The Parent Unit may
pick up signals or interference from other nursery monitors in your area. Your
monitor may even be picked up by other households. To protect your privacy, make
sure both units are turned OFF when not in use. If you experience interference,
change the channel on both units.
30. Power cord protection - Protect the Sensor Pad, cord and Adapter's
power cord from being walked on or pinched by furniture or other items
– Power supply cords should be routed so that they are not likely to be walked on
or pinched by items upon or against them, paying particular attention to cords and
plugs, convenience receptacle, and the point where they exit from the product. The
socket outlet shall be installed near the equipment and shall be easily accessible.
Make sure to plug the adapter to the socket outlet nearest to the equipment
and that is easily accessible. To disconnect from mains, unplug the adapter.
31. Only use attachments/accessories and replacement parts specified
by the manufacturer. Any mounting of the product should follow the
manufacturer's instructions.
• DO NOT position this product on an unstable cart, stand, tripod, bracket
or table. The product may fall, causing serious injury to a child or adult and
serious damage to the product.
• Use ONLY with a cart, stand, tripod, bracket or table recommended by the
manufacturer or sold with the product.
• Be sure replacement parts are supplied by Angelcare and have the same
characteristics as original part. Unauthorised substitution may result in fire,
electric shock or fire.
32. Unplug this appliance during lightning storms or when not used
for long periods of time
33. Servicing - DO NOT attempt to service this product yourself as
opening or removing covers (except battery door) may expose you to
dangerous voltage or other hazards.
34. Power Supply – see Technical Specification within this guide.
35. Overloading - DO NOT overload wall outlets, extension cords or
integral convenience receptacles as this can result in a risk of fire or
electric shock.
36. Nursery Unit Antenna - The antenna used for this transmitter must be
installed to provide a separation distance of at least 8'' (20 cm) from all persons
and must not be collocated or operating in conjunction with any other antenna
or transmitter.
37. Cleaning - Disconnect all units before cleaning. DO NOT immerse in water
any part of the monitor. Clean only with dry cloth.
38. Sensor Pad –
• Vibration Source/interference - When the Sensor Pad is in use, DO
NOT use a crib mobile, other crib accessories that may produce vibrations.
Other sources of vibrations may include fans, washing machines, loud music,
etc. These sources of vibration may interfere with the performance of your
Angelcare® monitor and the alarm will not sound if it continues to detect any
movement other than your baby's. Be sure all vibration sources are eliminated
before using the monitor.
• Sensor Pad can only be used in any crib that is stationary on a completely
flat, firm surface. If the crib has a spring or slat base, place a hard board
between the crib base and the Sensor Pad measuring at least 33 x 33 cm (13"
x 13") and 6 mm (1/4") thick. Box this safety instruction or move to instruction
section for setting up sensor pad or repeat
• The sensor pad is made of plastic and does not permit the air to
circulate. Therefore, mildew build up could develop underneath the mattress
in the sensor pad area. We suggest rotating the mattress regularly to prevent
any mildew.
39. False alarms may happen for several reasons:
• Nursery Unit has not been turned OFF after you have removed your baby
from the crib.
• Sensor Pad has not been placed under the mattress properly. Be sure the
Sensor Pad is on a flat, firm surface with the printed side facing up.
• The sensitivity level may also need to be adjusted. Refer to User's Guide.
Always be sure to immediately check on baby whenever an alarm sounds.
WARNINGS
40. Modifications not authorized by the manufacturer may void users authority
to operate this device.
40.1 NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
40.2 However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment
OFF and ON, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
40.3 This device complies with the part 15 of the FCC Rules and the Industry
Canada license - exempt RSS standards(s). Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
IC Warning :
41. This device complies with industry Canada RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including inferences that may
cause undesired operation of the device.
41.1 Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

FCC AND IC REGULATIONS

RF radiation exposure statement
The Nursery Unit complies with FCC RF radiation exposure limits set
forth for an uncontrolled environment.
Caution: To maintain the compliance with the FCC's and Industry
Canada's RF exposure guideline, install the Nursery Unit at least 7.9"
(20 cm) from ALL persons. The transmitter of this device must not
be co-located or operating in conjunction with any other antenna
or transmitter.
Industry Canada
This product meets the applicable Industry Canada technical
specifications.
CAN ICES-3 (B)/NMB-3 (B)
E
N
3