Pressure Setpoint - Franklin Electric SUBDRIVE UTILITY UT2W 5870202003 Serie Manuel Du Propriétaire

ON
"HP Values"
Pollution Degree 2
Degré de pollution 2
Grado de Contaminación 2
Solid State Motor Protection:
115 to 120 percent Full
Load Current
Protection de moteur à
semi-conducteurs: 115 à
120 pour cent de pleine
charge
Protección del motor de
estado sólido:
115 a 120% corriente a
plena carga
Suitable for use on a circuit
capable of delivering not
more than 5000 rms
symmetrical amperes, 250
V maximum.
Convenable pour utilisation
sur un circuit capable de
livrer pas plus de 5000
ampères symétriques pae,
250 V maximum.
Adecuado para utilizarse
en un circuito capaz de

PRESSURE SETPOINT

entregar no más de 5.000
amperes RMS simétricos,
250 V como máximo.
NOTE: Monitor pressure gauge during initial startup to ensure system does not overpressurize.
For SubDrive Pressure Sensor
The pressure sensor communicates the system pressure to the SubDrive Utility controller. The sensor is preset at the factory to 50 psi (3.4 bar),
but can be adjusted by the installer using the following procedure:
A. Remove the rubber end cap.
B. Using a 7/32" Allen wrench (provided), turn the adjusting screw clockwise to increase pressure and counterclockwise
to decrease pressure. The adjustment range is between 25 and 80 psi (1.7 and 5.5 bar).
NOTE: 1/4 turn = approximately 3 psi (0.2 bar).
C. Replace the rubber end cap.
D. Cover the pressure sensor terminals with the rubber boot provided.
Do not place the boot in direct sunlight.
For Analog Pressure Transducer
The pressure setpoint MUST be adjusted only when the SubDrive is POWERED OFF. The new setting will
not take effect until the drive is powered up.
When using an optional 4-20mA analog pressure transducer, the desired system pressure is set by
using the pressure setpoint adjustment knob (see figure above). The knob is factory set at 50% of the
transducer range and is adjustable from 5% to 95% of the transducer range in 5% increments. Refer to
the indicator lines surrounding the knob and corresponding legend printed on the adjacent shield when
setting the desired pressure setpoint. Table 6 to the right shows the conversion for percentage settings
and resulting psi values for several popular transducer ranges.
NOTE: The pressure setpoint knob is only compatible with an analog pressure transducer.
An analog pressure transducer must be installed in the system and DIP SW2:1 must be in the
XDCR (up) position to use this pressure adjustment.
22
RÁPIDO
1/3 1/2 3/4 1 1.5 115V XDCR
230V PS
SW1
P2
1
ON
1
J5
R14
R20
R12
RS485
D7
U5
INTERBOARD
R70
TP3
R15
R13
TP4
J3
EGND
C4
P1
C2 C1
U1
D10
R63
R64
J11
USB
> 75°C
230 VAC Cu
> 300 V
5 in-lbs
(0.55 Nm)
FAST MED SLOW
MEDIO LENTO
VITE MOYEN LENT DD SF BP
SW2
8 1 8 1
2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4
SW1 SW2
R23
D4
R16
J9
C25
R38
R109
C22
Y2
R22
U4
C21
C22
C19
C20 C10
R27
U3
TP2
TP1
R148
C102
C66
R251
D34
R135
MH1 MH2
Q6
R134
R9
R137
D35 R7 R8
Q5
C5
D5
D1 226115103 REV 2
R18 R17
TVS1
CONTROL PCB
R2
L1
T2 D3
D2 R1
RV2
U2
RV1
XDCR
PS FAN
R3
J6 J1 J13
1 1 1
24 S
PRESSURE
P
SENSOR TRANSDUCER FAN
5 in-lbs
(0.55 Nm)
WARNING – Retain Owner's Manual. Installation and
operation of this equipment requires detailed
instructions as provided in the Owner's Manual.
AVERTISSEMENT - Conserver le manuel du
propriétaire. L'installation et le fonctionnement de cet
équipement nécessite des instructions détaillées
fournies dans le manuel du propriétaire.
ADVERTENCIA – Conserve el Manual de Usuario. Para
la apropiada instalación y operación de este producto,
se requiere seguir detalladas instrucciones contenidas
en el Manual del Usuario.
ON
LT AB BD
+
ST
SW3
-
P4
8
ON
Underload
5 6 7 8
Sensitivity
SW3
DEFAULT
Potentiometer
PAR DÉFAUT
PREDETERMINADA
Pressure
UNDERLOAD
R36
UNDERLOAD
Setpoint
SOUS-CHARGE
CARGA BAJA
Potentiometer
% (PSI)
40 50 60
30
20
PRESSURE
SET POINT
10
PRESSURE
TRANSDUCER
P3
CAPTEUR
DE PRESSION
TRANSDUCTOR
DE PRESION
> 75°C
230 VAC M Cu
> 600 V
5 in-lbs
(0.55 Nm)
Table 6: Pressure Setpoints
%
100
5 5
10
10
15
15
20 20
25 25
30 30
35
35
40 40
45 45
50 50
55 55
60
60
65 65
70 70
75 75
80
80
85
85
90 90
95 95
70
80
90
Transducer Range (psi)
120 150 200
6 7 10
12 15 20
18 22 30
24 30 40
30 37 50
36 45 60
42 52 70
48 60 80
54 67 90
60 75 100
66 82 110
72 90 120
78 97 130
84 105 140
90 112 150
96 120 160
102 127 170
108 135 180
114 142 190