Gallignani GA FB 12 Manuel D'utilisation Et D'entretien page 119

On- -board computer functions - - Fig. 7
-- At the switching--on, the on--board computer (key
re. 1, fig. 7) presets to carry out the pre--set wrapping
type (manual or automatic, with twine or net).
The display, re. 7, shows the writing:
TWINE MANUAL
TWINE AUTO
NET MANUAL
NET AUTO
-- To change the pre--set wrapping function, press the
key, re. 2, fig. 7, auto/man.
-- To select twine or net, press the key with the twine/
net symbols, re. 3, (select "NET" only if the net
wrapper is fitted).
-- When the bale reaches the preset density, the com-
puter makes a beep for 2 seconds, then it operates
the motor for twine or net wrapping start (depending
on the selection made in the previous item).
The display, re. 6, shows the writing:
WRAPPING.
-- At the wrapping time end, the display, re. 7, shows
the writing: INSERT END.
This writing is displayed for a few seconds, followed
by the initial writing depending on the wrapping type
set. Wait until the wrapping process ends, then eject
the bale.
NOTE: if the manual wrapping has been selected
(both with twine or net); the on- -board computer buz-
zer operates until the wrapping control motor is oper-
ated manually, by the key, re. 1, fig. 7.
On- -board computer calibrations - - Fig. 7
-- To enter the "Calibration mode", press the con-
firmation (ENTER) key, re. 4, and hold it pressed for
3 seconds; the display shows the writing:
Setup - - Sw Vers. V01.01
corresponding to the on--board computer software
release.
In the calibration mode, pressing the key, re. 4, se-
quentially, the following functions can be displayed or
modified:
- - LANGUAGE: "English"
Available languages:
Italian, English, French, German and Spanish
To select, use the keys + and - -, re. 2 and re. 3.
- - Net Tm. 6 Sec
The writing "6" corresponds to the seconds of motor
operation to start net wrapping. The enabling time
can change from 1 to 30 seconds, through the keys
+ and - -, re. 2 and re. 3.
Usually, the time required for the correct net wrap-
ping goes from 6 to 8 seconds.
- - Twine Tm. 8 Sec
The writing "8" corresponds to the seconds of motor
operation to start twine wrapping. The enabling time
can change from 1 to 30 seconds, through the keys
+ and - -, re. 2 and re. 3. Usually, the time required for
the correct twine wrapping goes from 8 to 10 se-
conds.
- - Bales .. .. .. ..
Bale total counter (followed by the total number of
bales made); this value cannot be deleted.
- - BalePart. .. .. .. ..
Bale partial counter (followed by the number of par-
tial bales); to cancel the bale partial number, press
the key, re. 1, fig. 7.
- - Part.Cnt .. .. : .. ..
Bale hour counter (followed by the number of partial
hours and minutes of computer switching--on); to
cancel the hour partial number, press the key, re. 1;
fig. 7.
- - Counter .. .. : .. ..
Hour total counter (followed by the number of total
hours and minutes of the computer switching--on);
this value cannot be deleted.
This last function "Counter" is the last function of the
on--board computer; thus, by further pressing the
confirmation (ENTER) key, re. 4, you quit the calibra-
tion system.
NOTE: whenever the confirmation (ENTER) key, re.
4, is pressed, the displayed data item is stored, pas-
sing to the next function.
During the data reading and calibration, the on- -
board computer is inoperative. Before restoring work
or switching the computer off, press the key, re. 4, fig.
7, until the writing relevant to the set wrapping time
is displayed, corresponding to the data reading and
calibration quitting.
SECTION 2
E
N
G
L
I
S
H
2- -7