Code Learning; Deleting The Learned Data - Arcam HDA SA30 Manuel

Customising the Remote Control

Code learning

The supplied remote comes with a complete library
of pre-programmed codes. After you have set up the
remote for your device, you may find that there are one
or more functions on your original remote which do
not have a place on the keypad. For convenience, the
remote offers a Code Learning feature that allows you to
copy up to 16 functions from an original remote control
onto the remote keypad.
Before you start, make sure that:
The original remote control is working correctly.
The remotes are not pointing at your device.
The remotes have fresh batteries.
The remotes are not in direct sunlight or under
strong fluorescent lights.
NOTE: Learned functions are mode-dependent. You
could assign up to eight different functions to a single
key – a separate learned function for each mode.
Direct code setup (Method 1)
The first method is to program the remote with the
3-digit code number for the device you wish to control
– see "device code tables". Make a note of the suggested
number or numbers – the most popular code is listed
first. Now power on the device.
1. Press the Device key for the product you want to set
up, together with the key. Hold down both buttons
for three seconds until the LED stays lit. You are now
in setup mode, and you can release the buttons.
2. Enter a 3-digit code for the device. If the 3-digit code
number you entered is correct for the device, it will
turn off. If it doesn't turn off, enter the next code
number from your list until the device does turn off.
3. Once you have found the correct code, press
the Device key again. The LED blinks three times
*** to confirm that the code has been
successfully stored.
Library search setup (Method 2)
Library search allows you to scan through all the codes
contained in the remote's memory. It can take a lot
longer than the previous method, so only use this
method if:
Your device does not respond to the remote after
you have tried all the codes listed for your brand.
Your brand is not listed at all in the Device Code
tables.
Press the Device key for the product you want to set
up, together with the key. Hold down both buttons for
three seconds until the LED stays lit
Point the remote control at the product you wish
to control and press the ' or , button on the
navigation pad. Each time the ' or , button is
pressed, the code counts up (or down) one code
number with a signal to power off the device.
4. Continue pressing the up or down button, in
approximately one second intervals, until the device
turns off. (DO NOT alternate the up and down
button – you need to move in only one direction.)
5. To store the correct code, press the Device key again.
The LED blinks three times *** to confirm that
the code has been successfully stored.
Learning setup (Method 3)
The third method involves 'teaching' the Arcam remote
from the original remote for the device. The two
remotes should be facing each other, about 10cm apart.
1. Press the Device key for the product you want to
set up, together with the key. Hold down both
buttons for three seconds until the LED stays lit.
2. Press the button on the Arcam remote that you
want to assign a command to. The LED blinks once
* indicating that the remote is ready to learn the
command.
3. Press and hold the appropriate key on the other
remote until the LED blinks twice ** . This
indicates the Arcam remote has learned the
command from your other remote.
4. Continue learning the commands from your other
remote by pressing the next button on the remote
and repeating steps 2 and 3.
5. Once the remote has learned all the selected
commands, press and hold the Device key you used
to enter learning together with the Numeric key to
store the learned commands.
NOTE: If the Arcam remote LED blinks five times
***** there was an error in the learning
process. In this case, please start the Learning Setup
from the start.
The and keys do not learn commands.
Important notes
Once you start a Code Learning session, you have
approximately ten seconds to conduct each step.
Any longer, and a timeout means that you'll have to
start the process again.
The Learning feature is mode-specific – you can copy
one feature per mode onto a key.
The remote can learn approximately 16 functions in
total.
To replace a learned function, simply assign a new
function to the same key.
Learned functions are retained when you change
batteries.
If Code Learning fails, try altering the distance
between the two remotes; make sure that the
ambient light is not too bright.

Deleting the learned data

To delete all the learned data for a device:
1. Press the Device key for the product you want to
set up, together with the key. Hold down both
buttons for three seconds until the LED stays lit.
2. Press and hold down the Device key for the product
that you want to erase, together with the 4 key for
three seconds until the LED blinks twice ** .
3. If any further key press is not made for 30 seconds
after the LED blinks twice ** , the remote leaves
erase mode without deleting the learned data.
4. If you press the Device key one more time within
30 seconds after LED blinks twice ** , you can
finish the erase mode deleting all the data learned
on the Device. The LED blinks three times ***
to confirm.
EN-22
To delete the learned data for a key for a device:
1. Press the Device key for the product you want to
set up, together with the key. Hold down both
buttons for three seconds until the LED stays lit.
2. Press and hold down the key on which you want
to delete the data for three seconds. The LED blinks
twice ** . If any further key press is made, the
remote escapes from erase mode without deleting
the learned data.
3. If any further key press is not made for 30 seconds,
the LED blinks twice ** , the remote get out of
the erase mode automatically without deleting the
learned data.
4. If you press the Device key together with the key
again within 30 seconds after the LED blinks twice,
all the data learned for that Device is deleted and
you leave erase mode. The LED blinks three times
*** in confirmation.
Reading stored code numbers
1. Press the Device key for the product that you want
to set up together with the key. Hold down both
keys for three seconds until the LED blinks.
2. Press the key and count the number of blinks
( * =1, ** =2, *** =3, etc.). There is a time
gap between digits. (Note that '0' is represented by
ten blinks: ********** .)