Meaning Of The Symbols - Sime RS Mk.II Instructions Pour L'utilisateur

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 79
CONTROL UNIT (optional)
Follow the instructions provided below to make the best use of your "RVA 43.222/109" control unit::
TO TURN ON THE HEATING
– Turn on the main switch.
– Set the correct hour of the day and the day of the week.
– Place in automatic mode with the button
TO SET THE HOUR
Select the
Display
line
1
2
HOW TO USE THE AUTOMATIC MODE
In the automatic mode the temperature of the room is regu-
lated on the basis of the periods of heating chosen.
– Push the button
.
NOTE: Select the heating periods according to one's daily
requirements; in this way it is possible to significantly
save on energy.
TO ACTIVATE CONTINUOUS HEATING
The continuous heating mode keeps the temperature of the
room at the set level via the regulating knob.
– Push the "Continuous Operation" button
– Regulate the room temperature with the
regulating knob.
TO SET THE STANDBY MODE
(when the user is away for a long period of time)
The standby mode keeps the temperature of the room at
the level of antifreeze protection.
– Push the "Standby mode" button

MEANING OF THE SYMBOLS

On the display a few of the symbols indicate the current ope-
rating state. The appearance of a line under one of these
symbols signals that the corresponding operating state is
"active".
Heating at the nominal temperature
(regulating knob)
Heating at reduced temperature (line
Heating at antifrost protection temperature
(line
15
).
NOTE: For further information on the symbols and the
operating state refer to the detailed description of the
heating plant.
TO VARY THE HOT WATER PRODUCTION
The production of hot water can be activated or deactivated
by the push of a button.
– Push the button "Hot water"
IF THE HOT WATER IS TOO HOT OR TOO COLD
Select the
Display
line
13
74
.
Set the regulation
with the buttons
hour of the day
day of the week
.
.
14
).
.
Set the desired
temperature
°C
IF THE ROOMS ARE TOO HOT OR TOO COLD
– Check that current operating state on the display.
– In the case of nominal temperature
Increase or reduce the temperature of the room with the
regulating knob.
– In the case of reduced temperature
Select the
Display
line
14
NOTE: After each regulation wait at least two hours for
the new temperature to expand through the room.
TO CHANGE THE HEATING PERIODS
Select the
Display
Pre-select the weekly block
line
or the single day
5
With reference to the day chosen set the changes
as following:
Period
Push
Display
requested
button
6
Start
7
End
8
Start
9
End
10
Start
11
End
NOTE: The heating periods automatically repeat on a
weekly basis.
To this end select the automatic mode.
It is possible to reset the standard programme on line 23
by pushing the buttons + and – at the same time.
IF THE HEATING DOES NOT WORK PROPERLY
– Refer to the detailed documentation
on the heating system, following the fault finding
instructions.
TO MEASURE GAS COMBUSTION
– Push the "chimneysweep" button
The heating will work according to the level requested.
HOW TO SAVE ENERGY WITHOUT FOREGOING ON COMFORT
– A temperature of around 21°C is advised in the rooms
that are used. Every degree above this will increase hea-
ting costs by 6–7%.
– Aerate the rooms only for a brief period, opening the win-
dows completely.
– In the rooms that are not used place the regulating valve
in the antifreeze position.
– Leave the space in front of the radiators free from
obstructions (remove furniture, curtains...).
– Close windows and blinds to reduce
dispersion of heat.
.
.
Change the temperature
with the buttons
°C
1-7 = week
1 = Lu/7 = Do
Set
For
hour
°C
.

Publicité

Table des Matières
loading

Table des Matières