Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Upslope Arc length
Lichtbogenlänge beim Stromanstieg
Downslope arc length
Lichtbogenlänge beim Stromabstieg
Cold Arc length
Lichtbogenlänge beim Zweitstrom
Cratter Arc length
Lichtbogenlänge (Füllung)
Speed
Thickness
Current
Self
Voltage
Time spot
Dauer des Schweißpunktes
Time delay
Diameter
Material
Arc length range lock
Gesperrte Lichtbogenlänge
Speed range lock high
Hohe gesperrte Geschwindigkeit
Speed range lock low
Niedrige gesperrte Geschwindigkeit
TORCHES IN OPTION
- Push Pull torch (option ref. 046283)
The Push Pull torch is connected to the connector (FIG 1 - 15).
Using a Push Pull torch will enable the use of AlSi wire even Ø 0.8 mm with a 4m torch. This torch can be used on any mode.
The detection of the Push-Pull torch is made by a simple press on the trigger.
When using a potentiometer controlled push-pull torch, the interface's settings allow you to set the maximum value of the adjustment range.
The torch's potentiometer can then be used to adjust between 50% and 100% of this value.
Connection diagram for Push Pull
torch with potentiometer (10 kΩ)
3
5
2
1
4
- Spool Gun torch (option ref. 041486)
The Spool Gun torch is connected to the connector (FIG 1 - 14).
This torch can be used only in synergic, standard and manual mode.
- In manual mode, the knob to adjust the wire speed is on the torch (adjustment cannot be done on the machine).
- In synergic mode, the adjusting knob enables to amend the wire speed between 50% to 100% of the interface value.
The detection of the Push-Pull torch is made by a simple press on the trigger.
Procedure of reel assembly on Spool Gun torch :
4
5
1
AUTOPULSE 320-T3
N
N
N
Y
Geschwindigkeit
Y
Breite
Y
Strom
Y
Drossel
Y
Spannung
N
N
Wartezeit
N
Durchmesser
Y
Werkstoff
Y
Y
Y
Y
+4
1
3
4
7
-5
10
8
1
The digital torch works as follow:
1- Green light (speed:
2- Push button: Setting choice
3- Orange light (arc height:
4- Incrementing (speed or arc according to button 2)
5- Decrementing (speed or arc according to button 2)
1- Button opening/closing casing
2- Reel tightening nut
3- Reel break nut (do not tighten too much)
4- Adjsutment screw for rollers tension
5- Adjustment knob for speed wire
- Open the case (1), remove the support nut (2).
- Untighten the reel brake nut (3).
- Insert your reel.
- To insert the wire in the rollers, put a tension on the «adjustment screw for rollers
tension (4)»
- Remove the torch wire by reeling the reel.
3
2
- Plug in the Spool gun command connector and power connector
Y
Y
N
N
N
-40/+40
Y
Y
N
N
N
-40/+40
N
Y
N
N
N
-40/+40
Y
Y
N
N
N
-40/+40
Y
Y
Y
Y
Y
Y
Y
N
Y
Y
0,1-25,5
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
-40/+40
N
N
Y
Y
Y
N
N
N
Y
Y
0,1-10
N
N
N
N
Y
0,1-10
Y
Y
N
Y
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
+Pot 10
2
R
-Pot 3
+
-
8
M
)
)
0
1
No
0
1
No
0
1
No
0
1
No
2-22
1
0,1
m/min
1
0,1
mm
5-400
No
1
A
0
1
No
10-40
10
0,1
[V]
1
0,1
[S]
2
0,1
[S]
File
1
existe
No
File
1er
existe
No
±40
±20
±1
No
+10
+10
1
No
-10
-10
1
No
DE
Y
Y
Y
Y
Y
Y
Y
Y
Y
X
X
X
X
51
Publicité
Table des Matières
