Lenze Global Drive 8200 vector Instructions De Montage page 150

Show/Hide Bookmarks
Commissioning
Code table
Code
No. Name
C0421* Free configuration
v analog process data
output words
1 AIF-OUT.W1
2 AIF-OUT.W2
3 CAN-OUT1.W1 /
FIF-OUT.W1
4 CAN-OUT1.W2 /
FIF-OUT.W2
5 CAN-OUT1.W3 /
FIF-OUT.W3
6 CAN-OUT1.W4 /
FIF-OUT.W4
7 CAN-OUT2.W1
8 CAN-OUT2.W2
9 CAN-OUT2.W3
10 CAN-OUT2.W4
72
Possible settings
Lenze Selection
Output of analog signals on bus
Analog signal source
8 0 Output frequency (MCTRL1-NOUT+SLIP)
0 1 Controller load (MCTRL1-MOUT)
255 2 Apparent motor current (MCTRL1-IMOT)
255 3 DC-bus voltage (MCTRL1-DCVOLT)
255 4 Motor power
255 5 Motor voltage (MCTRL1-VOLT)
255 6 1/output frequency (1/C0050) (MCTRL1-1/NOUT)
255 7 Output frequency with limits (NSET1-C0010...C0011) p q
255 8 Operation with process controller (C0238 = 0, 1):
Act. process controller value (PCTRL1-ACT)
255 Operation without process controller (C0238 = 2):
Output frequency without slip (MCTRL1-NOUT)
9 Ready for operation (DCTRL1-RDY)
10 TRIP fault message (DCTRL1-TRIP)
11 Motor is running (DCTRL1-RUN)
12 Motor is running / CW rotation (DCTRL1-RUN-CW)
13 Motor is running / CCW rotation (DCTRL1-RUN-CCW)
14 Output frequency = 0 (DCTRL1-NOUT=0)
15 Frequency setpoint reached (DCTRL1-RFG1=NOUT)
16 Q threshold reached (PCTRL1-QMIN)
min
17 I limit reached (MCTRL1-IMAX)
max
C0014 = -5-: Torque setpoint reached
18 Overtemperature (ϑ
19 TRIP or Q or pulse inhibit (IMP) (DCTRL1-IMP)
min
20 PTC warning (DCTRL1-PTC-WARN)
21 Apparent motor current < current threshold
(DCTRL1-IMOT<ILIM)
22 Apparent motor current < current threshold and Q
threshold reached (DCTRL1-(IMOT<ILIM)-QMIN)
23 Apparent motor current < current threshold and RFG
1: Input = output (DCTRL1-(IMOT<ILIM)-RFG-I=0)
24 Warning motor phase failure (DCTRL1-LP1-WARN)
25 Minimum output frequency reached (PCTRL1-NMIN)
26 Output frequency normalised without slip
(MCTRL1-NOUT-NORM)
EDK82EV903 DE/EN/FR 1.0
y ( )
- 5 °C) (DCTRL1-OH-WARN)
max
min
IMPORTANT
•
With Lenze setting, CAN-OUT1.W1 and
FIF-OUT.W1 are defined as digital outputs
and the 16-bit controller status word 1
(C0417) is assigned to them.
•
If you want to output analog values
(C0421/3 ≠ 255), the digital assignment
must be deleted (C0417/x = 255)!
Otherwise the output signal would be
incorrect.
24000 ≡ 480 Hz
16383 ≡ Rated motor torque with vector control
(C0014 = 4), otherwise rated active inverter
current (active current/C0091)
16383 ≡ Rated inverter current
16383 ≡ 565 VDC at 400 V mains
16383 ≡ 325 VDC at 230 V mains
285 ≡ Rated motor power
16383 ≡ Rated motor voltage
195 ≡ 0.5 × C0011
24000 ≡ 480 Hz
0 ≡ f < C0010
24000 ⋅ (f − C0010)
≡ f ≥ C0010
480 Hz
24000 ≡ 480 Hz
Selection -9- ... -25- corresponds to the digital p
f functions of the relay output K1 (C0008) or the i f h l K1 (C0008)
digital output A1 (C0117): digital output A1 (C0117):
LOW = 0 V/0 mA/4 mA LOW = 0 V/0 mA/4 mA
HIGH = 10 V/20 mA HIGH = 10 V/20 mA
Belt monitoring
Apparent motor current = C0054 pp
Current threshold = C0156
14
2 ≡ C0011
L
g
h