Lenze Global Drive 8200 vector Instructions De Montage page 143

Show/Hide Bookmarks
Code
No. Name
C0410 Free configuration of
v digital input signals
1 NSET1-JOG1/3
NSET1-JOG1/3/5/7
(A)
2 NSET1-JOG2/3
NSET1-JOG2/3/6/7
(A)
3 DCTRL1-CW/CCW
4 DCTRL1-QSP
5 NSET1-RFG1-STOP
6 NSET1-RFG1-0
7 MPOT1-UP
8 MPOT1-DOWN
9 Reserved
10 DCTRL1-CINH
11 DCTRL1-TRIP-SET
12 DCTRL1-TRIP-RESET
13 DCTRL1-PAR2/4
14 DCTRL1-PAR3/4
15 MCTRL1-DCB
16 (A) PCTRL1-RFG2-
LOADI
17 DCTRL1-H/Re
18 PCTRL1-I-OFF
19 PCTRL1-OFF
20 Reserved
21 PCTRL1-STOP
22 DCTRL1-CW/QSP
23 DCTRL1-CCW/QSP
24 DFIN1-ON
L
Possible settings
Lenze Selection
Linkage of external signal sources to internal digital
signals
Digital signal source
1 0 Not assigned (FIXED-FREE)
255
2 1 ... 6 Digital inputs X3/E1 ... X3/E6 (DIGIN1 ... 6)
X3/E1 (1) ... X3/E6 (6)
E5, E6 only application I/O
4 7 PTC input (X2.2/T1, X2.2/T2)
255 10 ... 25 AIF control word (AIF-CTRL)
Bit 0 (10) ... bit 15 (25)
255
255 30 ... 45 CAN-IN1.W1/FIF-IN.W1
Bit 0 (30) ... bit 15 (45)
255
CAN-IN1.W2/FIF-IN.W2
255 50 ... 65
Bit 0 (50) ... bit 15 (65)
255
255
255 70 ... 85 CAN-IN2.W1
Bit 0 (70) ... bit 15 (85)
255
255 90 ... 105 CAN-IN2.W2
Bit 0 (90) ... bit 15 (105)
255 140 ... Status application I/O
172 as C0415, selection 140 .. 172
3 200 Bit-by-bit assignment of the FIF control words y g
(FIF-CTRL1, FIF-CTRL2) from the function module (FIF CTRL1 FIF CTRL2) f
255
INTERBUS or PROFIBUS-DP (see C0005)
255
201 ...
255 Digital output signals
231 231
255 201 as C0415, selection 1
255 ... ...
255 231 as C0415, selection 31
255
255
255
EDK82EV903 DE/EN/FR 1.0
Commissioning
( )
h f i d l
Code table
IMPORTANT
•
A selection made under C0007 is copied
to the corresponding subcode of C0410.
A change of C0410 sets C0007 = 255!
Selection of fixed setpoints
C0410/1 C0410/2 active
C0410/33
C0046
LOW LOW LOW LOW LOW LOW
JOG1 JOG1
HIGH LOW LOW
JOG2
LOW HIGH LOW
...
... ... ...
JOG7
HIGH HIGH HIGH
CW = CW rotation LOW
CCW = CCW rotation HIGH
Quick stop (via terminal LOW active)
Ramp function generator main setpoint stop
Ramp function generator input must be set "0"
for mains setpoint
Motor potentiometer functions p
Controller inhibit (via terminal LOW active)
External error (via terminal LOW active)
Error reset
Parameter set changeover
(only possible, if C0988 = 0)
C0410/13 and C0410/14 must have the same
source in everey parameter sets used.
Otherwise it is not possible to change
between the parameter sets.
C0410/13 C0410/14 active
LOW LOW PAR1
HIGH LOW PAR2
LOW HIGH PAR3
HIGH HIGH PAR4
DC-injection brake
Actual process controller value (PCTRL1-ACT)
must be connected to process controller ramp
function generator (PCTRL1-RFG2)
Manual/remote changeover
Process controller switch off
Process controller stop (value "frozen")
Failsafe change of the direction of rotation g
0 = Frequency input not active
1 = Frequency input active
Frequency input configuration under C0425 and
C0426
65