Lenze Global Drive 8200 vector Instructions De Montage page 133

Show/Hide Bookmarks
Code
No. Name
C0117 Fixed configuration of
v
digital output A1
(DIGOUT1) (
C0119 Configuration of g
v
motor temperature
monitoring (PTC
input) / earth fault input) / earth fault
detection
2
C0120 I t switch-off
C0125* LECOM Baud rate
v
C0126* Response in the
v v
event of
communication
errors errors
C0127 Setpoint selection
v v
C0128 Service code
L
Possible settings
Lenze Selection
0
)
0 ... 16
255
0
0
1
2
3
4
5
0 0
= not active
0
0
1
2
3
4
10
i ti
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
0
0
1
see C0008
Free configuration under C0415/2
Earth fault detection
PTC input not active
active i
PTC input active
TRIP set
PTC input active
Warning set
Earth fault detection
PTC input not active
PTC input active
TRIP set
PTC input active
Warning set
{1 %}
9600 baud
4800 baud
2400 baud
1200 baud
19200 baud
Communication channel
AIF FIF FIF-CAN
0 0 0
CE0 0 0
0 CE5 0
CE0 CE5 0
0 0 CE6
CE0 0 CE6
0 CE5 CE6
CE0 CE5 CE6
0 0 0
CE0 0 0
0 CE5 0
CE0 CE5 0
0 0 CE6
CE0 0 CE6
0 CE5 CE6
CE0 CE5 CE6
Absolute setpoint selection in Hz via C0046 or
process data channel
Setpoint selection normalised via C0141 (0... 100 %)
or process data channel (±16384 = C0011)
EDK82EV903 DE/EN/FR 1.0
Commissioning
Code table
IMPORTANT
Changes of C0117 will be copied to C0415/2.
Free configuration under C0415/2 sets
C0117 =255!
Only display
Do not change C0117 since settings under
C0415/2 can be lost
•
Signal output configuration under C0415 g p g
•
Deactivate the earth fault detection if it is
activated unintentionally
200 Reference: Apparent motor current (C0054)
Only for LECOM-A (RS232) y (
Configuration of the response in the event of
communication abort
GATEWAY
0 CEx = monitoring active
0 = monitoring not active 0 = monitoring not active
0
•
AIF
– Monitoring of the communication in the
0
process data channel with field bus process data channel with field bus
0
modules on AIF
– Communication abort at active monitoring Communication abort at active monitoring
0
activates TRIP CE0 activates TRIP CE0
•
FIF
0
– Monitoring of the internal communication – Monitoring of the internal communication
0
between the FIF module and drive
controller t ll
0
– Communication abort at active monitoring – Communication abort at active monitoring
activates TRIP CE5
CE7
• •
FIF-CAN FIF-CAN
CE7
– Monitoring of the communication (bus Monitoring of the communication (bus
OFF) with field bus module system bus
CE7
(CAN) on FIF (CAN) on FIF
CE7
– Communication abort at active monitoring
activates TRIP CE6 activates TRIP CE6
CE7
•
GATEWAY GATEWAY
– Monitoring of remote parameterisation via
CE7
C0370 C0370
CE7
– Communication abort at active monitoring
activates TRIP CE7 ti t TRIP CE7
CE7
Modifications only by Lenze Service!
)
g
55