Setting The Clock; Listening To Radio - SOUNDMASTER NR546 Guide D'utilisation

Precautions for use
Installation

Unpack all parts and remove protective material.

Do not connect the unit to the mains before checking the main voltage and before all other connections have been made.

Do not cover any vents and make sure that there is a space of several centimeters around the unit for ventilation.
Connection
1. Plug in the AC cord (34) to the AC outlet. Switch the unit to standby mode by Main power switch (33). The unit will go to
standby mode and the LCD display will dim light up.
2. Turn on the unit (4), if the LCD display (6) is on with backlighting, it means the power supply is normal. Now your system is
ready to play the music.

Setting the clock

1. Set unit in standby mode.
Press the "Mem/Clk-Adj" button (21) until display flashes "24HR". Press the Skip Up
2.
to select the clock format between 12 or 24Hour. Then press the "Mem/Clk-Adj" button (21).
The first digit of "0:00" is flashing on the LCD display (6). Press Skip Up
3.
correct hour. Press "Mem/Clk-Adj" button (21) to store the correct hour.
The third & fourth digit of "00" is flashing, press the Skip Up
4.
minutes. Then press "Preset/Clk-Adj" button (21) to store the correct minute.

The clock setting mode will automatically quit if no button is being pressed in a period of about 5 seconds after
pressing the "Mem/Clk-Adj" button.

Listening to radio

Manual tuning
1. Plug in the provided DAB/FM tuner antenna to the antenna socket (32) then switch on the unit by On/Standby button (4),
then press Function button (5) to select "FM" mode.
2. Tune to the required station by tuning knob (23).
3. Turn the Volume knob (17) to the desired volume level.
Auto tuning
1. Set the unit to FM mode.
2. Press the Scan button (20) once; unit will start to scan at tuning up direct until radio station received. Press and hold the
Scan button (20) for a second, the unit will scan to tuning down direction. If the radio data system (RDS) broadcasting signal
received, the unit will set the actual time automatically.
3. Turn the Volume knob (17) to the desired volume level.
Radio data system (RDS)
This is the features to display the information which released from the radio broadcast and will showed on LCD display step by
step as below by pressing the Info button(on the remote control) continuously.
Radio text  program type  signal strength  date/time  frequency  mono/stereo
Digital audio broadcasting (DAB) radio
Set the unit to "DAB" mode by Function button (5).
1.
2. Press the Scan (20) button once; unit will start to full scan from range 11b-12d one time within around 2 second. Then press
Tune up/down button (14/15) to select your desired DAB channel.
3. Press the Info button continuously to check the below info released by DAB.
Group name  frequency  transfer rate  signal strength  date/time  program type  scrolling text
4. Press the Volume knob (17) to the desired volume level.
Preset stations
You can store up to total of 40 radio stations in the memory (20-FM/20-DAB).
1. Set to FM/DAB mode
Turn to the desired radio station by "manual" or "auto" tuning method.
2.
3. Press and hold the Mem/Clock-Adjust button (21) around four second to enable memory state, the preset station will flash
on LCD display.
4. Preset the Skip/ Pre up/down button (14/15) to select the desired station memory for storage.
5. Press Mem/Clock-Adjust button (21) to confirm the preset memory.
6. Repeat step 2 to 5 to store other stations.
NR546 / English Instruction Manual
or Skip Down
or Skip Down
or Skip Down button (14/15) to set the correct
button (14/15)
button (14/15) to set the
3