Setting the clock
Set unit in standby mode.
1.
Press and hold the " Mem/Clk-Adj " button (12) until display will flash "24HR" press the Skip Up
2.
button (23/13) to select the clock format between 12 or 24Hour. Then press the " Mem/Clk-Adj " button (12).
The first digit of " 0:00 " is flashing on the LCD display (2). Press Skip Up
3.
correct hour. Press " Mem/Clk-Adj " button (12) to store the correct hour.
The third & fourth digit of " 00 " is flashing, press the Skip Up
4.
minutes. Then press " Preset/Clk-Adj " button (12) to store the correct minute.
➢
The clock setting mode will automatically quit if no button is being pressed in a period of about 5 seconds after
pressing the " Mem/Clk-Adj " button.
Listening to FM radio
Manual tuning
1. Plug in the provided DAB/FM tuner antenna to the antenna socket (30) then switch on the unit by On/Standby button (6), then
press Function button (10) to select " DAB " mode then press Band button (16) to select FM mode.
2. Tune to the required station by pressing the Tuning Up or Down button (23/13).
3. Turn the Volume knob (19) to the desired volume level.
Auto tuning (on the remote control only)
Set the unit to FM mode.
1.
Press the Scan button once on the remote control, unit will start to scan at tuning up direct until radio station received. Press
2.
and hold the Scan button on the remote control for a second, the unit will scan to tuning down direction. If the radio data
system (RDS) broadcasting signal received, the unit will set the actual time automatically.
Turn the Volume knob (19) to the desired volume level.
3.
Radio data system (RDS)
This is the features to display the information which released from the radio broadcast and will showed on LCD display step by
step as below by pressing the Info button(on the remote control) continuously.
Radio text→ program type→ signal strength→ date/time→ frequency→ mono/stereo
Digital audio broadcasting (DAB) radio
Set the unit to "DAB" mode by Function button (10).
1.
Press the Scan button on the remote control once, unit will start to full scan from range 11b-12d one time within around 2
2.
second. Then press Tune up/down button (23/13) to select your desired DAB channel.
Press the Info button continuously to check the below info released by DAB.
3.
Group name→ frequency → transfer rate →signal strength→ date/time→ program type → scrolling text
Press the Volume knob (19) to the desired volume level.
4.
Preset stations
You can store up to total of 40 radio stations in the memory (20-FM/20-DAB).
Set to FM/DAB mode
1.
Turn to the desired radio station by " manual " or " auto " tuning method.
2.
Press and hold the Mem/Clock-Adjust button (12) around four second to enable memory state, the preset station will flash on
3.
LCD display.
Preset the Folder/ Pre up button (22) to select the desired station memory for storage.
4.
Press Mem/Clock-Adjust button (12) to confirm the preset memory.
5.
Repeat step 2 to 5 to store other stations.
6.
Recall preset stations
Press the Mem/Clock-Adjust button (12) once to enable recall state
1.
Press Folder/ Pre up button (22) to select the desired memory station.
2.
Press Memory/Clock-Adjust button (12) to confirm the recall memory station.
3.
➢
There are 3 seconds for program state, after 3 sec. This state would resume to normal tuner mode automatically.
You can overwrite a present station by storing another frequency in its place.
➢
MCD5550 / English Instruction Manual
or Skip Down
or Skip Down
3
or Skip Down
button (23/13) to set the
button (23/13) to set the correct