Engine Stopping; Oil Change - Güde ECO WHEELER 410 P Traduction Du Mode D'emploi D'origine

1. Primary pump (13) to be pressed three times!
2. Press the operation lever (automatic switching off lever)
(12) to the mobile handle (1).
3. With the operation lever (automatic switching off lever) (12)
pulled in slowly pull out the starting cord (9), when you feel slight
resistance strongly pull in the starter until the engine is started.
CAUTION: In cold weather or when the machine has not
been used for a longer time it may be necessary to repeat
the first steps for several times.

ENGINE STOPPING

If you want to stop the engine release the operation lever
(automatic switching off lever) (12).
WARNING! The knife still rotates for a few seconds after
the engine is switched off. If you want to leave the mower laying
unattended then disconnect the spark plug cap.
Important tips and advice for grass cutting!!!
Under certain conditions, e.g. when the grass is very high, it
•
may be necessary to adjust bigger cutting height so that effort at
pushing the mower was reduced, engine overloading removed
and blocking of grass in the mower prevented. It is possible you
will also have to reduce the mower travel speed and/or cut the
area again.
• If cutting is very difficult it may be suitable to reduce the travel
speed and mower gear.
• Vent ports in the grass catcher may get blocked if the catcher is
not cleaned regularly. Clean the grass catcher regularly with
water and let it dry before use.
Keep the upper part of the engine in the
•
starter place clean. Air flow will be improved
and engine life increased by doing so.
• Cut in dry weather only.
Always keep the knives sharp.
•
MAINTENANCE
IMPORTANT – Regular maintenance is unavoidable for
constant operational reliability and keeping the original device
output.
1) Keep all screws and nuts tightened so that you were sure the
device is in an operation-reliable condition. Regular
maintenance is necessary for safety and trouble-free
operation.
2) Never store the device with fuel in closed rooms as the
evaporating fuel may ignite.
3) It is necessary to let the device cool down and empty fuel
from it before storing in closed rooms.
4) In order to minimise the risk of fire keep the engine and
muffler and the fuel tank clean and with no grass,
leaves and fats. Do not store the grass cut with the
mower.
5) For safety reasons, avoid using a device with a worn or
damaged parts. Replace any faulty parts with new ones,
do not repair them. Use original spare parts and original
spare knives only.
Parts with quality different from the one prescribed may
damage the device and threaten your safety.
6) If it is necessary to empty the fuel tank do it outside and with
cold engine.
7) Wear solid protective gloves at assembly and adjustment of
knives.
8) Check correct direction of rotating and balance of knives
after sharpening.
9) Regularly check wear and pollution of the self-closing cover
and grass catcher.
10) When you must transport the device, carry it in hands or
incline it always wear safety gloves.
Always hold the device at places guaranteeing safe holding.
Take into account the weight of the device and its distribution.
ČLEANING
Clean the device with water, remove the grass and mud from
inside before each use – it will prevent from impurities getting dry
and problems at next starting.
KNIFE DISASSEMBLY
For purpose of cleaning / sharpening / replacement
Attention!!! It is necessary to first disconnect the spark plug
before disassembly.
Release the screw at disassembly of the knives.
Re-assemble according to the picture. Tighten the screws. Torsion
moment of 40 Nm. You should also replace the screw at
replacement of knives.

OIL CHANGE

The stopper for oil emptying is placed under the engine. Make
sure you have a container for oil catching prepared and
disassemble the stopper. As soon as the oil flows out insert a
new stopper with a washer and wipe oil remnants.
Add new SAE30 oil to the tank. Measure the oil level with a
clean gauge. The oil must reach between min. and max.
marking on the gauge. Make sure you do not overfill the tank.
Start the engine and let running for a short time. Then switch
it off, wait for a minute and measure the oil level. If necessary,
add some oil.
Spark plug
When the engine cools down disassemble the spark plug with
the key supplied, clean it with a wire brush and adjust the
distance to 0.75 mm (0.030") through a feeler gauge. Then re-
fit the spark plug. Make sure you do not tighten it too firmly.
14
Screw for oil emptying