Assembly Preparation - Güde ECO WHEELER 410 P Traduction Du Mode D'emploi D'origine

•
Always wear protective glasses when operating the
mower.
•
Remove all obstacles, e.g. stones and branches.
•
Check the terrain for unevenness, there may be
obstructions hidden in high grass.
•
Do not cut near ditches and slopes. You may lose your
stability and balance.
•
Do not use the device on a very steep terrain.
•
Realise the operator, or, more precisely, the user is
responsible for any injuries or threat of persons and
things.
•
Be watchful and switch the device immediately off if there
are children around.
•
Be watchful and switch the device immediately off if there
are children around.
•
Never let persons not familiarised with these instructions
work with the mower. The operator's age can be limited
by local regulations.
•
WARNING — petrol is highly flammable.
Store the fuel in containers designed for that purpose.
o
Add fuel outdoor only, do not smoke when adding
o
fuel.
Add fuel before device starting. Never take the cover
o
out and do not add fuel when the engine is running or
hot.
- If you spill the petrol do not try to start the device.
o
Take the device away and prevent generation of a
flammable source around the spilled petrol.
Secure the petrol tank is closed safely.
o
•
Always check whether the knife, knife bolts and cutting
equipment are not damaged or worn before using the
mower. Always replace any damaged and worn knives
and bolts in the entire set to prevent device unbalance.
Do not make any alterations to the safety device.
Regularly check their proper functioning.
•
Keep the device clean, with no grass, leaves or other
impurities. Always wipe any oil or petrol run out. Let the
mower cool down before storing to closed spaces.
•
Be especially careful when changing direction on a slope.
•
Never adjust the height of wheels when the engine is
running.
•
The grass catching device may lose its functioning any
throw away items due to wear or damage. Regularly
check the mower parts and, if necessary, replace them
with spare parts recommended by the manufacturer.
•
The mower knife is very sharp. Risk of injury! Be
especially careful at knife maintaining, wear protective
gloves or cover the knife-edges.
•
Do not change the basic engine adjustment and avoid its
overloading.
•
Be especially watchful when turning the mower or pulling
it towards your body.
•
If it is necessary to incline or lift the mower to pass a
surface other than grass or when carrying the mower to or
from the area to be cut then cut off the knife.
•
Release the knives and engine clutches before switching
on.
•
Start the engine in accordance with the operating
instructions and make sure your legs are in safe distance
from the knife.
•
Do not incline the mower at starting except for cases
when it is necessary. Do not incline the mower more than
necessary in such a case and always lift the part reversed
from you.
•
Do not start the engine when standing in front of the
ejection outlet.
•
Never lift and transfer the mower with engine running.
•
Lower the brake adjustment when the engine is off. If the
engine is equipped with a stop valve then close the petrol
supply after cutting.
•
Move slowly if using an auxiliary trail seat.
ASSEMBLY / PREPARATION
All assembly and/or maintenance works may be
performed only when the motor is turned off!
Please read the entire operating instructions before
assembling or starting your new mower.
IMPORTANT: The mower is supplied without oil and
petrol.
UNPACK THE MOWER
Take the mower out of the board and check whether there are
any free parts left there.
Assembly of collecting bag (Fig.3-5)
1. Take the collecting bag, corresponding frame and
plastic insert out of the package. (Fig. 3)
2. Put the frame into the collecting bag while paying
attention to that the coupling at the frame is outside
the collecting bag. (Fig. 4)
3. Now fix the collecting bag at the frame. (Fig. 5)
Assembly - Handle
1. Press the handle into the holes of the chassis and secure
with one screw (15).
2. Remove the protection sleeve, lift the upper parts of the
handle and assemble it with the bottom part. Tighten the
safety bolts on both sides of the handle.
Remove the protection sleeve of the operation grab
3.
handle in the upper part.
Installation of wheels, sticks and handle
Left side/left thread
Step 2
Installation of
sticks
1. Wheel bolts marked "L" are for wheels that are on the left
from the operator's view. Caution – left thread! Wheel
bolts marked "R" are for wheels that are on the right from
the operator's view. Caution – right thread! The spark
plug wrench included is also suitable for the installation of
wheels.
2. Press both sticks to the openings in the support frame to
the full extent and fixate them using the included bolts.
3. Push the handle to the sticks and secure it using the
included bolts and wing nuts. The starter cable holder
needs to firmly screwed down on the side of the reversing
starter.
12
Right side/right thread
Step 1
Installation of wheels
Step 3
Installation of
handle