Electrical Safety; General Safety; Inspect Your Shipment; Package Includes - Franklin Electric Inline 1100 Manuel Du Propriétaire

NOTiCe indicates special instructions which are
important but not related to hazards.
Carefully read and follow all safety instructions in this
manual and on pump.
W A R N I N G
HAZArDOuS PreSSure: Do not run
pump against closed discharge. Release all system
pressure before working on any component.
C A U T I O N
Do not run pump dry. Fill pump with water
before starting or pump will be damaged.
This Inline Constant Pressure System is guaranteed by
the manufacturer. In the event of a product failure, it
must be returned to an authorized water system
professional for repairs. Warranty is void if repairs are
not made by an authorized technician.

electricAl SAfety

C A U T I O N
Make sure all ELECTRICAL POWER IS
OFF before connecting any electrical wires.
W A r N i N g
Hazardous voltage.
Can shock, burn, or
cause death.
Ground pump before
connecting to power
supply. Disconnect
power before working
on pump, motor or
tank.
C A U T I O N
DO NOT touch an operating drive.
surface of the drive may be HOT. Allow the drive
to cool for thirty (30) minutes before handling.
Suitable for use on a circuit capable of
delivering not more than 5000 rMS symmetric
amperes, 260 volt maximum.
The output connector on the drive is only
intended for use with the motor specifi ed in the
replacement Parts section of this manual.
integral solid state short circuit protection
does not provide branch circuit protection.
Branch circuit protection must be provided in
accordance with the National electric Code or
Canadian electric Code and local codes.

GenerAl SAfety

The Franklin Electric Inline System is designed and built
with a NEMA 4 approved drive enclosure to protect the
pump's electronic components.
Wire inline System for
correct voltage. See
"electrical installation"
section of this manual and
inline System nameplate.
Connect power supply
ground to ground terminal
in wiring compartment
before connecting power
supply.
Meet National electrical
Code (NeC) or Canadian
electrical Code (CeC) and
local codes for all wiring.
Follow all pump wiring
instructions provided in this
manual.
inline SyStem Key feAtureS
SyStem feAtureS:
• Constant water pressure with a wide range of
settings. (10-80 psi, 0.7 - 5.5 bar)
• Pump speed is controlled to provide the optimum
performance without overloading the motor
• Product Power Rating: 1.2 hp (0.9 kW)
• Low current motor start-up (soft-starting)
• Quiet operation
• Single pump/motor/drive controller design
• Compact footprint, 19 in x 8 in (480 mm x 200 mm)
• Shipping weight: 50 lbs (22.7 kg)
pump feAtureS:
• Operates on a wide range of fl ows from fl ooded
suction to 35 GPM (135 LPM)
• Requires minimum incoming pressure of 3 PSI
(0.2 bar) Exception: Cisterns may be fl ooded suction
without vortexing
• Increases incoming pressure by up to 60 PSI (4.1 bar)
• Stainless steel construction for all wetted surfaces
drive controller protection feAtureS:
• No in-rush (power-on transient) current
• Over pressure shut off optional
(See Replacement Parts Section)
• Low water shut off
• Locked pump detection/shut off
• High voltage/lightning surge protection
• Low line voltage protection
• Motor under and overload protection
• Open and short circuit protection
• NEMA 4 enclosure

inSpect your SHipment

The
All Franklin Electric Inline Systems are carefully tested,
inspected, and packaged to insure their arrival in perfect
condition. When the pump is received, examine it closely
to make sure there is no damage that may have occurred
in shipping. If damage is evident, report this immediately
to your shipping carrier and product dealer. The shipping
carrier assumes full responsibility for the shipment's
safe arrival. Any claim for damage to the shipment,
either visible or concealed, must be made through the
shipping carrier fi rst.

pAcKAGe includeS:

• Inline 1100 Constant Pressure System pump
and controller unit
• Pressure sensor and boot
• Sensor adjustment tool
• Installation manual
1