gefran 1600 Manuel D'utilisation page 25

Hrd
Hardware configuration
Auxiliary input
hrd. 1
installation, digital
inputs, serial
interface.
Timer and multiset
enabling
Installation of
hrd. 2
relay, logic
outputs
MAIN, AL1,
AL2, AL3,
and analogue
outputs W1,
W2
hrd. 3
0
(trl
Control type
[0...78]
43
s. S . t .
Start / Stop Timer
-
r. t .
Reset Timer
--
(0 ... 15)
hrd.1 Aux Logic Logic
analogue input 1 input 2
input (IN1) (IN2)
0
1 x
2 x
3 x x
4 x
5 x x
6 x x
7 x x x
8
9 x
10 x
11 x x
12 x
13 x x
14 x x
15 x x x
+16 to enable the Timer function
+32 to enable the Multiset function (2SP)
+64 to enable the Multiset function (4SP)
hrd.2 OUT 1 OUT 2 OUT 3
(relay, logic) (relay, logic) (relay, logic) (relay, logic)
0
1 x
2 x
3 x x
4 x
5 x x
6 x x
7 x x x
8
9 x
10 x
11 x x
12 x
13 x x
14 x x
15 x x x
+ 16 to enable analogue output W1
+ 32 to enable analogue output W2
+ 64 to invert state of LEDs compared to state of output
Non significant
function
CtrL Control type
0 P heat
1 P cool
2 P heat / cool
3 PI heat
4 PI cool
5 PI heat / cool
6 PID heat
7 PID cool
8 PID heat / cool
9 ON-OFF heat
10 ON-OFF cool
11 ON-OFF heat / cool
12 PID heat + ON-OFF cool
13 ON-OFF heat + PID cool
14 PID heat + cool with relative gain
(see C.MEd parameter)
Selection of derivative action
sampling time:
+ 0 sample 1 sec.
+ 16 sample 2 sec.
+ 32 sample 8 sec.
+ 64 sample 240 msec.
Note: LbA alarm is not enabled with
ON/OFF type control
0 from enabled digital input
1 from AL1 ON
2 from AL2 ON
3 from AL3 ON
4 from ALHB ON
5 from serial line (address 0049H, bit 0)
6 from serial line (address 0049H, bit 1)
7 from keys
+8 inverse action
+16 Autoreset enabled (Stop = program reset)
(only for _S.S.t. parameter)
• Hrd
sens
probe type for
Serial
interface
x
x
x
x
x
sns. 2
Selection of probe
x
type for aux input
x
x
OUT 4
al. n r
Select number of
enabled alarms
x
x
x
x
x
x
x
x
butt
Function of M/A
but. 2
d. i . f . 1
Function of digital
d. i . f . 2
Function of digital
disp
25
SEnS Probe type for main input
Selection of
0 Thermocouple (TC)
1 Resistance Thermometer (RTD)
main input
2 Thermistor (PTC)
3 Voltage 0...50mV / 10...50mV
4 Current 0...20mA / 4...20mA
5 Voltage 0...10V / 2...10V
6 Custom 10V
7 Custom max 50mV
+ 8 to enable main input curve 4 point correction
(alternative to custom linearization).
See description in "Main Input Correction
Function" section.
+16 to disable averaging filter on sampled
value (available from software release 3.05)
Note: scale selection with "tYPE" code in InP
SnS.2 Signal
0 0 ... 1V
1 0.2 ... 1V
2 0 ... 10V
3 2 ... 10V
4 0 ... 20mA
5 4 ... 20mA
6 Potentiometer
7 CT 50mA
+8 to disable averaging filter on sampled value
(available from software release 3.05)
AL.nr Alarm 1
0 disabled
1 enabled
2 disabled
3 enabled
4 disabled
5 enabled
6 disabled
7 enabled
+ 8 to enable HB alarm
+ 16 to enable LBA alarm
b u t t
0 No function (key disabled)
1 MAN / AUTO controller
2 LOC / REM
3 HOLD
4 Start / Stop selftuning
keys: "*"
5 Start / Stop autotuning
6 Set / Reset outputs Out 1... Out 4
7 Alarms memory reset
8 SP1 / SP2 Selection
9 Integral contribution instantaneous
zero setting
10 Start / Stop Timer
(se S.S.t. = 7)
11 Reset Timer
(se _rt = 7)
+16 disable function in configuration menu
Non significant
0
function
d.i.F.1, d.i.F.2
0 No function (disabled input.)
1 MAN / AUTO controller
2 LOC / REM
3 HOLD
input 1 (IN1)
4 Start / Stop timer
5 Reset timer
6 Software on/off
7 Alarms memory reset
SP1...SP2 (2SP) Selection
8
input 2 (IN2)
SP1...SP4 – bit Lo Selection
9 SP1...SP4 – bit Hi Selection
+ 16 for inverse logic input
+ 32 to force logic state 0 (OFF)
+ 48 to force logic state 1 (ON)
diSP Lower display (SV) function
0 SSP - setpoint enabled
(*)
1 InP.2 - aux input
Defining SV (*)
2 Control output value
display function (*)
3 Deviation (SSP - PV)
(*)
8 Visualisation of current time on PV
display and tS time on SV
display
+ 4 Timer in start
(*)
~
Alarm 2 Alarm 3
disabled disabled
disabled disabled
enabled disabled
enabled disabled
disabled enabled
disabled enabled
enabled enabled
enabled enabled