Short-Time Centrifugation; Change The Settings During The Centrifugation Run; Emergency Stop; Acoustic Signal - Hettich ROTINA 380 Mode D'emploi

EN
17.3

Short-time centrifugation

A short-time centrifugation is not possible if program linkages are being used.
•
Keep the key pressed. The LED in the
START
subsequently lit. The time count starts from 00:00.
•
Release the key again to end the centrifugation run. Run- down is carried out with the selected run- down
START
parameters. The run-down parameter is displayed e.g.
Once the rotor has come to a standstill, the LED in the
switch off and the left LED in the
During the centrifugation run, the speed of the rotor or the RCF value resulting from this, the sample temperature (for
centrifuges with cooling only) and the time run will be displayed.
18

Change the settings during the centrifugation run

It is not possible to modify settings during centrifuge operation if program linkages are being used.
The running time, the speed, the relative centrifugal force (RCF), the centrifuging radius, the run-up and run-down
parameters as well as the temperature (for centrifuges with cooling only) can be changed while the centrifuge is
running.
•
Select the parameter you want and use the
centrifugation parameter").
•
Press the key. The changed setting is saved at program place "0" (see chapter "Automatic temporary
START
storage"). The program place number is displayed in parentheses (0). The original program is not overwritten.
19

Emergency Stop

•
Press the key twice.
OPEN / STOP
During a not-stop, run-out is carried out with braking level 9 (shortest run-out). Braking level
braking level 0 has been preselected, run-out is carried out with braking level
time is longer, technically speaking, than braking level 9.
20

Acoustic signal

The acoustic signal sounds:
•
Upon the appearance of a disturbance in 2 second intervals.
•
After completion of a centrifugation run and rotor standstill in 30 second intervals.
The acoustic signal is stopped by opening the lid or pressing any key.
The signal after completion of the centrifugation run can be activated or deactivated in the following manner, if the
rotor is at standstill:
•
Keep the key held down for 8 seconds.
PROG
After 8 seconds, ∗∗∗ Machine Menu ∗∗∗ appears in the display.
•
Press the key as often as necessary until the ->Settings is displayed.
PROG
•
Press the key. The SOUND / BELL = off/on is displayed.
START
•
Use the adjusting knob
•
Press the key to save the setting.
START
Briefly, Store Settings ... is displayed as confirmation, followed by -> Settings.
•
Press the key once to leave the "Settings" menu or press the
OPEN / STOP
"Machine Menu".
21

Displayed centrifugation data after switch-on.

After switch-on the centrifugation data from program 1, or from the last program that was used, is displayed.
If the rotor is at standstill, this can be set as follows:
•
Keep the key held down for 8 seconds.
PROG
After 8 seconds, ∗∗∗ Machine Menu ∗∗∗ appears in the display.
•
Press the key as often as necessary until the ->Settings is displayed.
PROG
•
Press the key. The SOUND / BELL = off/on is displayed.
START
•
Press the key as often as necessary until Start program = Last/First is displayed.
PROG
•
Use the adjusting knob
Last = the program used last, First = program 1.
•
Press the key to save the setting.
START
Briefly, Store Settings ... is displayed as confirmation, followed by -> Settings.
•
Press the key once to leave the "Settings" menu or press the
OPEN / STOP
"Machine Menu".
44/134
key blinks until the rotor has been imported, it is
START
key lights up.
OPEN / STOP
adjusting knob to change the value (see chapter "Enter
to set off or on.
to set Last or First.
9. The right-hand LED in the
key and the right LED in the
START
9d. With braking level 9d, the run-out
OPEN / STOP
OPEN / STOP
key is lit.
OPEN / STOP
key
OPEN / STOP
9 is displayed. If
key twice to leave the
key twice to leave the