Lewmar Pro-Serie Manuel D'installation, De Fonctionnement Et D'entretien page 15

KIT NO DESCRIPTION
66000096 Pro-Series Stripper Arm Kit
66000098 Pro-Series Clutch Nut & Cone Kit
Clutch Lever
66000099
504 Gypsy RC 8mm (5/16")
66000101
516 Gypsy RC 5/16" G4
66000102
Pb Gypsy (14-16mm Leaded Line)
66000768
Dual Gypsy RC 6mm - 7mm -1/4"
66000769
66000634 Bearing Kit
66000616 Pro-Fish Conversion Kit
66000617 Pro-Fish Stopper Kit
66000620 Pro-Fish Drive Cap Assembly Kit
Pro-Series Washer Kit
66000758
66000759 Pro-Series Gasket Kit
66000760 Pro-Series Coumpound Gear kit
Pro-Series Gears & Shaft Kit
66000761
Pro-Series Gear Train Cover Kit
66000762
Pro-Series 12V Motor Kit
66000763
Pro-Series Seals & Screw Kit
66000764
66000766 Pro-Guard / Control Arm Kit
8- Troubleshooting
1. Anchor rode pays out independently while windlass is not in use.
• This problem is a result of not securing the anchor rode combined with the gypsy drive cap being slack.
Tighten the gypsy drive cap using the winch handle and always secure the anchor rode independently of the
windlass when not in use.
2. Failure to operate or sluggish operation.
• The majority of these problems are electrical in nature. It is essential that the proper voltage be maintained.
The proper voltage on a 12 Volt system is 13.5 Volts, constant low voltage will damage motor.
• Ensure electrical cable size is large enough to handle the current draw and keep voltage drop within
acceptable limits.
• Check control switches, connections, battery condition, isolator switch, fuse and motor for operation failure.
3. Failure to operate.
• Is there a voltage at the input terminals to the contactor and switches. Check the circuit breaker/isolator
switch and any fuses.
• Operate the switch. Is there voltage at the positive switch terminal on the solenoid. If not, the switch (or its
wiring), is difective.
• Keep the switch activated. Is there voltage at the main output terminal on the contactor. If not check the
contactor coil ground circuit. If okay, replace the contactor.
• Check the voltage at the motor. If voltage of at least 12.5 volts is present and the motor does not operate, the
motor is defective.
ITEMS INCLUDED (QTY)
37(1), 53(1), 54(2)
35(1), 36(1), 43(2)
Clutch lever (not shown)
58A(1)
58B(1)
58C(1)
58(1)
2(1), 4(1), 5(1), 6(2), 56(1), 57(1)
8(1), 9(1), 10(1), 11(1), 12(1), 13(1),14(1), 15(1), 16(1), 17(1), 20(1), 54(2)
9(3), 54(2)
8(1), 10(1), 11(1), 12(1), 13(1),14(1), 15(1), 16(1), 17(1), 20(1)
21(1), 22(1), 23(2), 27(1)
24(1), 25(6)
5(1)
2(1), 3(1), 6(2), 23(2), 28(1), 33(1), 34(1), 45(1), 46(1), 51(1)
4(1), 18(1), 24(1), 25(6). 42(1), 55(6), 57(1)
26(1), 33(1), 38(1), 45(1), 50(2), 52(3)
2(1), 3(1), 7(1), 24(1), 25(6), 26(1), 39(2), 42(1), 43(2), 45(1), 52(3), 53(2), 54(3), 55(6)
29(1), 30(1), 31(1), 41(1), 44(1), 48(1), 54(3)
Lewmar Pro-Series/Fish windlass ref B10414 iss.2
|
15