Indication Of Power Supply Failure At The Last Welding; Configuring The Welding Unit; Understanding The "Settings" Sub-Menu - Hürner HST 300 GeoTherm+ 2.0 Manuel Utilisateur

H Ü R N E R S c h w e i s s t e c h n i k G m b H
Nieder-Ohmener Str. 26
35325 Mücke, Germany
8.4

Indication of Power Supply Failure at the Last Welding

The message "Power Supply Failure Last Welding" indicates that
the previous welding aborted because of a power supply failure.
The reason may be too weak a generator or too long or too thin an
extension cable, or a tripped cut-out in the mounting box. The next
welding operation is still possible after acknowledging the message
by pressing the STOP/RESET key.
9 Configuring the Welding Unit
With the operator identity card, the welding unit can be reconfigured.
When the MENU key is pressed, the "Enter Menu Code" message ap-
pears on the screen. After the code was read from the operator card,
the selection menu in Display 9 shows.
At "Settings," the parameters related to the welding unit itself and
its operation can be set. At "Recording," the traceability data that
have to or need not be recorded and written into the reports can be
enabled or disabled. The desired sub-menu is selected using the ñ and
ò arrow keys. Then to access that sub-menu, press the MENU key.
In both parts of the configuration menu, use the ñ and ò arrow keys
to select the desired set-up option. Use the ð arrow key to toggle
between "on" and "off" for that set-up option.
If a "M" is shown next to a set-up option, this indicates that a sub-
menu is accessible here by pressing the MENU key.
Press the START/SET key to confirm the set-up and save it to
memory.
9.1

Understanding the "Settings" Sub-menu

"Check Code Expiry on" means that the welder identification code has
to be current and not expired (default period of validity 2 years
from code issuance), or the welding operation cannot be started,
"off," that the validity of the code is not checked at all.
"Memory Control on" means that when the system memory is full of
reports, the unit will be blocked until the reports are printed or
downloaded, "off," that it works but that the oldest report will
be overwritten.
"Welder Code Options – M – " means that by pressing the MENU
key, the user can access a sub-menu that allows determining
when the welder code, if it is enabled at "Recording," has to be
entered:always, i. e. before evey single welding operation, only
before the first welding operation after switching the unit on or
only after the first welding operation of a new day/date.
"Language – M – " means that by pressing the MENU key, the user
can access a sub-menu for selecting the display and report lan-
guage (see Sect. 9.1.1).
"Date/Time – M – " means that by pressing the MENU key, the user
can access a sub-menu for setting the clock (see Sect. 10.1.2).
"Buzzer Volume – M – " means that by pressing the MENU key, the
user can access a sub-menu for setting the volume of the status
buzzer (see Sect. 9.1.3).
"Temperature Unit – M – " means that by pressing the MENU key, the
user can access a sub-menu for selecting centigrade or Fahrenheit
as the unit for the temperature.
Version July 2013 HÜRNER HST 300 GeoTherm + 2.0 User's Manual
>Settings -M-
Recording -M-
Display 9
*** SET-UP MENU ***
>Check Cd Expiry off
Memory Control on
Wldr Code Option-M-
Display 10
*** SET-UP MENU ***
>Language -M-
Date/Time -M-
Buzzer Volume -M-
Display 11
*** SET-UP MENU ***
Buzzer Volume -M-
>Temp. Unit -M-
Display 12
EN
13