Connect Drain Hose - Maytag W10290309A Instructions D'installation

Connect drain hose

3
Connect drain hose to waste tee or waste disposer
using one of the following options:
• Option A, Waste disposer - no air gap
• Option B, No Waste disposer - no air gap
• Option C, Waste disposer - with air gap
• Option D, No waste disposer - with air gap
IMPORTANT: The drain hose connection of the disposer or a
waste tee must be made before the drain trap and at least 20"
(50.8 cm) above the floor where the dishwasher will be installed.
Helpful Tip: To reduce vibration of the hose, keep the hose away
from the floor.
Option A, Waste disposer – no air gap
Waste disposer – no air gap
Disposer inlet Disposer inlet
1. Using a hammer and screwdriver, knock
1
plug into disposer.
2. Use needle-nose pliers to remove plug.
2
3. Attach drain hose to disposer inlet with
large silver drain hose clamp (provided).
3
Use pliers to squeeze clamp open and
move into position.
Option B, No waste disposer – no air gap
No waste disposer – no air gap
Waste tee Waste tee Waste tee
Drain trap Drain trap
1. Connect black end of of drain hose to waste
1
Black end
tee and cut if needed.
NOTE: Do not cut ribbed section.
2. Attach black end of drain hose to waste tee
with a large silver drain hose clamp (provided).
2
Use pliers to squeeze clamp open and move
into position. If the drain hose was cut, use a
1¹⁄₂" to 2" (3.8 to 5 cm) screw-type clamp (not
provided).
Large silver
drain hose clamp
Drain hose
Drain trap Drain trap
Screw-type Large silver
drain hose clamp clamp
Drain hose
Option C, Waste disposer – with air gap
Waste disposer – with air gap
Screw-type clamps Screw-type clamps Screw-type clamps
Disposer inlet Disposer inlet
1. Using a hammer and screwdriver, knock
1
plug into disposer.
2. Use needle-nose pliers to remove plug.
2
3. Connect black end of drain hose to air gap
and cut if needed.
3 Black end
NOTE: Do not cut ribbed section.
4. Attach drain hose to air gap with large
silver drain hose clamp (provided). Use
4
pliers to squeeze clamp open and move
into position. If the drain hose was cut, use
a 1¹⁄₂" to 2" (3.8 to 5 cm) screw-type clamp
(not provided).
5
5. Use a rubber hose (not provided) with
screw-type clamps (not provided) to
connect from air gap to disposer inlet.
Option D, No waste disposer – with air gap
No waste disposer – with air gap
Screw-type clamps Screw-type clamps Screw-type clamps
Waste tee Waste tee
Drain trap Drain trap
1. Connect black end of drain hose to air gap
1
Black end
and cut if needed.
NOTE: Do not cut ribbed section.
2. Attach drain hose to air gap with large silver
drain hose clamp (provided). Use pliers to
2
squeeze clamp open and move into position.
If the drain hose was cut, use a 1¹⁄₂" to 2"
(3.8 to 5 cm) screw-type clamp (not
provided).
3
3. Use a rubber hose (not provided) with
screw-type clamps (not provided) to
connect from waste tee to air gap.
Air gap Air gap
Large silver drain Large silver drain
hose clamp hose clamp
(provided)
Rubber hose
connector
Drain hose
Drain trap
Air gap Air gap
Large silver drain Large silver drain
hose clamp hose clamp
(provided)
Rubber hose
connector
Drain hose
9