Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the recommended tools and parts before starting
installation. Read and follow the instructions provided with any tools
listed here.
All Installations
Tools needed:
Pliers
Phillips
screwdriver
nut drivers or
hex sockets
Measuring tape
or ruler
10" adjustable wrench
that opens to
*Must be the proper size to connect your household wiring to 16
gauge wiring in dishwasher
Other useful items you may need:
Flashlight
Shallow pan
Parts supplied:
Drain hose clamps (2)
(1 large and 1 small)
Green
Silver
Make sure all these parts are included in the literature package.
Parts needed:
Other parts you may also need:
(38.1– 5 cm)
Screw-type
clamps (3 maximum)
NOTE: Parts available for purchase in plumbing supply stores.
Check local codes. Check existing electrical supply. See "Electrical
Requirements" section. It is recommended that electrical connections be
made by a licensed electrical installer.
Flat-blade
screwdriver
Utility knife
UL Listed/CSA
Approved twist-on
wire connectors*
Small level
wrench
Bath towel
Wood block
Drain hose
Phillips-head
screws (2)
Side mounting kit
Masking or
for solid surface
duct tape
countertops
(Part Number
8212560)
In addition, for first-time installations
Tools needed:
Cordless drill
with ¹⁄₂", ³⁄₄"
and 1¹⁄₂" hole
saw bits
Parts needed:
Copper tubing (³⁄₈"
See "Electrical Requirements" section
O.D. suggested) or
For Direct Wire:
flexible braided
use UL Listed/
water supply line
CSA Approved
strain relief
to fit ⁷⁄₈" (2.2 cm)
hole
Location Requirements
Grounded electrical supply required.
Do not run drain lines, water lines or electrical wiring where
they can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must
provide clearance between motor and flooring. Motor should not
touch the floor.
Do not install dishwasher over carpeted flooring.
Avoid damage from freezing to dishwasher and water lines leading
to dishwasher. Damage from freezing is not covered by the
warranty.
A side panel kit is available from your dealer for installing
your dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part Number 4396277) is available
from your dealer for installing underneath the countertop.
Check location where dishwasher will be installed. The
location must provide:
• easy access to water, electricity and drain.
• convenient access for loading and unloading dishes.
Corner locations require a 2" (5.1 cm) minimum
clearance between the side of the dishwasher door
and the wall or cabinet.
• square opening for proper operation and appearance.
• cabinet front perpendicular to floor.
• level floor. (If floor at front of opening is not level with
floor at rear of opening, shims may be needed to level
dishwasher.)
Helpful Tip: Be sure to accurately measure dimensions
and ensure dishwasher is level if the floor in the dishwasher
opening is uneven (example: flooring extends only partway into
opening).
NOTE: To avoid shifting during dishwasher operation,
shims must be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it winterized by
authorized service personnel.
Make sure pipes, wires and drain hose are within the
shaded area shown in the "Product and Cabinet
Opening Dimensions" section.
Small
Wire stripper
tubing cutter
For Power Supply
Cord: use UL
listed power
supply cord kit
marked for use
with dishwasher
3
Publicité
Chapitres
Table des Matières
