Migatronic PILOT 1800 E Manuel D'instruction page 22

TECHNICAL DATA
Power source:
Mains voltage
Fuse
Consumption max.
Efficiency
Permitted load
- 35% duty cycle (40°C)
- 60% duty cycle (40°C)
- 100% duty cycle (40°C)
Open circuit voltage
Current range
1
Application class
2
Protection class (IEC 529)
Standards
Dimensions (W-H-L)
Weight (E-model)
Weight (H & HP-models)
Torch cooling module MCU:
Cooling capacity
Tank capacity
2
Protection class
Dimensions (W-H-L)
Weight
Functions: Process
Arc power Electrode
Hot-start Electrode
Anti-freeze TIG/Electrode
Pilot arc TIG
Start AMP TIG
Stop AMP TIG
Slope up TIG
Slope down TIG
Gas pre-flow TIG
Gas post-flow TIG
Spot welding time TIG
Pulse time TIG/Electrode
Pause time TIG/Electrode
Base AMP TIG/Electrode
Reduced current TIG
Setting of welding jobs TIG/Electrode
S
1
The machine meets the standards which are demanded of
machines working in areas where there is an increased risk of
electric shock
2
Equipment marked IP23 is designed for indoor and outdoor
applications
PILOT 1800 PILOT 2400
3x400 V ±15% 3x400 V ±15%
10 A 16 A
5.76 kW 8.64 kW
0.85 0.85
180 A 240 A
140 A 200 A
110 A 160 A
85 V 85 V
5 – 180 A 5 – 240 A
S S
IP 23 IP 23
EN/IEC60974-1 EN/IEC60974-1
EN/IEC60974-10 EN/IEC60974-10
22x40x50 cm 22x40x50 cm
18 kg 18 kg
20 kg 20 kg
0.5 kW 0.5 kW
2.2 liters 2.2 liters
IP 23 IP 23
22x21x50 cm 22x21x50 cm
26 kg 26 kg
PILOT 1800 / 2400
0-150 %, max. 180/240 A
0-100 %, max. 180/240 A
always active
4 %, min. 5 A
0-100 %, min. 5 A
0-100 %, min. 5 A
0-10 secs
0-10 secs
0-60 secs
3-20 secs
0.1-50 secs
0.01-10 secs
0.01-10 secs
1-99 %, min. 5 A
0-100 %, min. 5 A
16 (H & HP-models)
8 (E-model)
WARRANTY
All MIGATRONIC machines carry a twelve-month
guarantee against hidden defects. Such defects must be
notified no later than two months after it has been
noticed. The warranty runs for twelve months after
invoicing to end customer.
The warranty covers material and manufacturing faults
that cannot be immediately acknowledged.
Lapse of warranty
The warranty covers no obvious product characteristics,
which in time are thought as being inconvenient.
Incorrect installation
The warranty does not cover defects due to incorrect
installation of the product, e.g. connection to the wrong
mains voltage.
Incorrect or abnormal use of the product
The warranty does not cover use of the product for other
purposes than it has been designed for.
Lack of maintenance
There is a lapse of warranty if the product is not properly
maintained. E.g. if the product is dirty to such a degree that
cooling is hindered. The warranty does not cover damages,
which can be traced back to unauthorised and lacking re-
pairs of the product.
Over loading/extreme loading
The warranty does not cover over loading or extreme
loading. Nor transport damages, damages due to incorrect
handling, drops etc. The warranty does not cover abnormal
conditions as regards temperature, moisture or environ-
mental loading above the limit, which the machine has
been designed for.
Defects due to infestants
The warranty does not cover defects due to infestants.
Wear parts
The warranty does not cover parts of the product, which is
exposed to wear and tear, e.g. the welding torch and
welding cables. The warranty does not cover depreciation
due to normal use, e.g. scratches, rust and mechanical
damage. Welding cables and welding hoses are regarded
as wear parts and therefore not included in the warranty.
Resulting damages
Use of the product must stop immediately after acknow-
ledge of a defect in order to avoid further damage of the
product. The warranty does not cover resulting damages
due to use of the product after acknowledge of a defect.
Moreover, the warranty does not cover resulting damages
on other items due to product defect.
22