Tightening Rules For Torsion Springs; Tightening Rules For Extension Springs; Additional Requirements; Environmental Protection - Wisniowski UNIPRO Notice De Montage

EN
Fig. 105.1 After mounting, cut the protruding parts of the brackets and pro-
tect the edges with paint.
Fig. 105 Before operating the door, lubricate all hinges, rollers and springs
with, e.g. semi-solid HWS-100 Wurth grease.
Fig. 110 For manually operated doors with Ho>2200 [mm], mount the
cord facilitating the door closing.
Fig. A When mounting a drive, block the door bolts in its open position.
[D000012] 7. TIGHTENING RULES FOR TORSION SPRINGS
The number of spring turns is stated on the manufacturer's plate of the door.
To tighten the springs, steel rods are applied, which ends should conform to
the holes in spring drums. The person who tightens the springs should be cor-
respondingly trained, and no other people should stay in the vicinity. When
tightening, the person who tightens should stand on scaffoldings next to the
spring to ensure that the tightening rods and springs are not located in front
of him or her. Before starting the proper tightening, check if the springs are
securely fixed on drums, and if springs do not have visible cracks and defor-
mations. Then loosen the screws fastening spring drum with shaft. The tighten-
ing should be performed by ¼ revolutions till the required tension is achieved.
During tightening, insert one rod into the spring drum hole, and turn it to such
an angle as to enable the second rod to be inserted in the next spring drum
hole. When the second rod is securely fixed in the drum hole, remove the first
rod, but continue to hold firm the second rod. Repeat the procedure till the
required tension is achieved. During tightening, the spring will stretch and
decrease its diameter. When the desired tension is achieved, carefully tighten
the screws fastening spring drum with shaft. Then, remove the the tightening
rods. Repeat the procedure to tighten the second spring.
This Instruction provides exemplary number of spring turns. The actual num-
ber of spring turns may differ slightly from the number of turns stated on the
manufacturer's plate of the door. This is explained by specific conditions of the
particular door installation.
When the door installation is completed, check whether the door operates
according to the Assembly and Operating Instruction. If necessary, make cor-
responding adjustments.
Check the correct tension of springs, and, if necessary, adjust it. To do this:
• open the door by lifting its leaf to half-open position,
• if the leaf is visibly falling, increase the spring tension by its regulation,
• if the leaf is visibly lifting, decrease the spring tension by its regulation.
[D000020] 7.1. TIGHTENING RULES FOR EXTENSION SPRINGS
To tighten the springs, spring tensioners on the horizontal guide ends are
used. The person who tightens the springs should be correspondingly trained,
equipped with relevant safety clothes, and no other people should be present
in the vicinity. During tightening, the person who tightens the springs should
stand on scaffoldings behind the springs. Before starting the proper tightening,
ensure that the cables and mounting hooks are securely fixed. To tighten, pull the
tensioner and hook its proper hole to a vertical protrusion of the corner bracket
connecting the guide end with the cross-beam connecting both guides. On the
other side of the door, hook the tensioner to the same hole.
When the door adjustment is completed, protect the tensioners with split pins.
When the door installation is completed, check whether the door operates
according to the Assembly and Operating Instruction. If necessary, make cor-
responding adjustments.
Check the correct tension of springs, and, if necessary, adjust it. To do this:
• open the door by lifting its leaf to half-open position,
• if the leaf is visibly falling, increase the spring tension by its regulation,
• if the leaf is visibly lifting, decrease the spring tension by its regulation.
If the above mentioned works are not performed, there
is a risk that the leaf may suddenly fall down and hurt
people, or cause damage to objects in its vicinity.
[A000007] 8. ADDITIONAL REQUIREMENTS
After the installation is completed, it must be checked that the door is fitted with
CE data plate according to the standard. If this plate is missing, fit the door with
such a data plate. After verifying the correct operation of the door, the Assembly
and Operating Instruction and door report book, if required, should be handed
over to the Owner.
[A000015] Activities, which may be performed by the Owner after careful
reading of the Assembly and Operating Instruction supplied with the door.
When the door is installed, the protective foil should be
immediately removed from the door leaf.Failure to do
so will result in a strong adherence of the foil to the door
skin metal under the influence of temperature and sun
rays. This will make it impossible to remove the foil and
may lead to coating deterioration.
4
Assembly and Operating Instructions – Sectional garage door UniPro
[A000008] 9. ENVIRONMENTAL PROTECTION
Packaging
Elements of packaging (cardboard, plastics, etc.) are classified as waste suit-
able for recycling. Follow local legislation for specific material before throw-
ing it away.
Scrapping
The product consists of many different materials. Most of the materials used are
suitable for recycling. Sort it before disposal, and then deliver to refuse collec-
tion and disposal area for recycling.
Follow local legislation for specific material before
scrapping.
[A000009] Remember! Recycling of packaging materials
saves natural resources and reduces the amount of
wastes.
[C000022] 10. DOOR DISASSEMBLY
• Close and lock the door.
• Release the tension of door springs.
• Perform the assembly procedure in the reverse order.
[C000033] 10.1. DISSASSEMBLY OF SN DOOR
• Open the door and secure the leaf against falling down.
• Release the tension of door springs.
• Carefully close the leaf.
• Perform the assembly procedure in the reverse order.
[A000029] 11. OPERATING AND MAINTENANCE INSTRUCTION
The Assembly and Operating Instruction is a documentation intended for the
door owner.
Please read carefully this instruction and follow its recommendations. The
instruction includes information ensuring safe usage, operation and mainte-
nance of the door.
[A000010] 12. IMPORTANT INFORMATION AND NOTES
• Please carefully keep this instruction.
• All operating activities must be performed according to the door
Assembly and Operating Instruction.
• Occupational health and safety regulations and recommenda-
tions included in the Assembly and Operating Instruction must
be observed during all works related to the door inspections
and repairs.
• It is prohibited to change any door components or parts.
[B000006] 13. INFORMATION REGARDING FORBIDDEN DOOR
USAGE
• It is forbidden to open the door if the guides are not mounted.
• It is forbidden to obstruct the door movement area. When operat-
ing the door, make sure there are no people, especially children,
or objects within the door movement area.
• It is forbidden for people to stay, or leave cars or other objects in
a clearance of the opened door.
• It is prohibited to stay, walk, run or drive under the moving door.
• It is prohibited to use the door leaf to lift objects or people.
• Do not allow children to play with equipment. Transmitters for
door operation must be kept away from children. Transmitters
should be kept in dry, moisture-free places.
• It is forbidden to modify or remove any door components! This
may cause damage to parts ensuring the door safe usage.
• [B000010] It is forbidden to install any additional fillings or
thermal insulation in the door leaf without a written consent of
"WIŚNIOWSKI" Sp. z o.o. S.K.A. Springs are precisely adjusted
to the door leaf weight, and all additionally mounted elements
may cause its overload and incorrect door operation.
• [B000013] When the door is installed, the protective foil should
be immediately removed from the door leaf. Failure to do so will
result in a strong adherence of the foil to the door sheet metal un-
der the influence of sun rays. This will make it impossible to remove
the foil and may lead to paint coating deterioration.
• Doors with electric drive must be opened according to drive As-
sembly and Operating Instruction.
• [B000008] The door should be protected against harmful agents
(including corrosive agents, like acids, alkali, salts), which may
damage the paint coating and metal. The door should also be
IIiO/BS/UniPro/05/2014/ID-91262 Technical description
+