Falcon 1092 CT Dual Fuel Mode D'emploi page 28

Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
f ) Pull the appropriate lead from the sleeve and push in the
replacement.
g) Replace the leads in the rear upright.
h) Re-connect the leads at the generator and oven
electrode.
j) Re-assemble in reverse order and check ignition.
21 To Remove Oven Inner Back
a) Open the oven door. For the LH oven unscrew the 2
thermostat phial fixing screws. Remove the fixings that
secure the inner back to the oven rear.
b) Lift the removable panel away.
c) Re-assemble in reverse order. Ensure that the retaining
fixings are fully tightened.
22 To Replace an Oven Fan
Disconnect the appliance from the electricity supply.
a) Pull the unit forward to access the cover boxes at the
rear of the appliance. Remove the fixings that secure the
cover and lift it clear.
b) Remove the fan wiring, noting the connection positions.
c) Remove the inner back as detailed in Section 21.
d) Hold the fan blades and undo the centre nut (LH thread),
brass washers, fan blade and Circlip.
e) Undo the fixings that retain the fan and remove it from
the cavity rear.
f ) Fit the replacement and re-assemble parts in reverse
order. Check that the oven operates satisfactorily.
23 To Remove an Oven fan Element
Disconnect the appliance from the electricity supply.
a) Remove oven inner back (see 21).
b) Remove 2 screws from the top of the element and 1 from
the bottom of the element in side the oven.
c) Lift element out carefully, disconnect the terminals
connected to the element noting their positions. If it
is not possible to disconnect the leads in this way, pull
cooker forward to gain access to the rear, remove screws
securing the electric cover to the back sheet and remove
cover and disconnect the terminals from the rear.
d) Fit new element, and reassemble in reverse order.
e) Check that the oven operates correctly.
24 To Remove the Left Hand Oven Bottom and Top
Elements
Disconnect the appliance from the electricity supply.
Bottom Element
a) Pull the unit forward to access the cover boxes at the rear
of the unit. Remove the fixings that secure the cover and
lift it clear.
b) Undo the terminal connections, noting their positions.
c) Remove the fixings that secure the bottom element
cover.
d) Undo the terminal connections, noting their positions.
e) Remove the lower element support fixings.
f ) Remove the element bracket fixings and withdraw
element.
g) Replace the element and re-assemble parts in reverse
order.
SERVICING - WARNING
Top Element
a) Open the LH oven door and undo the fixings that secure
the heat shield.
b) Remove the top element bracket fixings and withdraw
element.
c) Replace the element and re-assemble parts in reverse
order. Check that the oven operates satisfactorily.
25 To Remove a Grill Element
Disconnect the appliance from the electricity supply.
a) Pull the grill carriage forward and lift the grill pan away
from the carriage. Lift the grill carriage so that the front
roller is free of the side arm. Slide the carriage forward on
the rear roller until you can lift it away from the side arm.
b) From inside grill compartment remove enamelled front
shield from grill roof, 2 screws and washers. Remove
2 screws and washers securing the grill element front
support.
c) Remove the screws from the grill elements. Lift elements
out carefully, disconnect the leads from the element
terminals noting their position.
d) If it is not possible to disconnect the leads in this way,
turn off the gas supply. Remove the drawer – lower the
front roller. Pull the cooker forward and disconnect the
gas hose. Pull the cooker far enough forward to gain
access to the rear.
e) Remove the fixings that secure the rear cover and lift it
clear. Disconnect the terminals from the rear.
f ) Fit new elements, reassemble in reverse order. Check
operation of grill.
26 To Adjust the Oven Door Angle
The door bottom hinge can be adjusted to alter the angle
of the door.
Loosen the bottom hinge fixing screws and use the notch
and a flat bladed screwdriver to move the position of the
hinge to set the hinge position.
Retighten the hinge screws.
Effect of hinge adjustment – exaggerated for clarity
Oven door omitted for clarity
28
Centre line of hinge pin