Falcon 1092 CT Dual Fuel Mode D'emploi page 27

Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
12 To Remove a Hotplate Burner
a) Remove the French cooktop, pan supports, hotplate
accessories and burner heads.
b) Remove the hotplate as detailed in Section 1.
c) Remove the nut that secures the burner body to the
support channel.
d) Remove the fixings that secure the support channel to
the chassis. Lift the channel clear of the appliance.
e) Undo the compression fitting which connects the burner
body to the gas pipe. Remove the burner body from the
appliance.
f ) Replace in reverse order. Check the appliance is gas
sound and that the burner operates satisfactorily.
13 To Remove the Oven Door
a) Open the oven door.
b) Support the door and remove the two screws which
secure the upper hinge to the front frame of the unit.
c) Remove the door from the lower hinge by lifting slightly
and moving it outward.
d) Re-assemble in reverse order.
14 To Remove the Grill Door
a) Remove the pan supports, hotplate accessories and
burner heads.
b) Remove the hotplate as detailed in Section 2.
c) Remove the control panel as detailed in Section 3
d) Remove LH side panel a detailed in Section 4.
e) Remove the kicker plate (4 screws).
f ) Remove the central vertical cover situated between the
ovens. (5 screws).
g) Remove the 2 countersunk screws (1 per side) which
secure the hinge arms to the front of the grill chamber.
Note
The door hinge arms are spring tensioned. Carefully
remove the grill door and retain the gaskets.
h) Re-assemble in reverse order. Ensure that the gasket is
fitted between the hinge arm and the front of the grill
chamber. Check door operation.
15 To Remove the Oven Outer Door Panel
a) Open the oven door.
b) Remove two screws 'A' and two screws 'B' from the door.
c) Remove the outer door panel.
d) Undo the nuts that secure the handle to the door panel.
Fit the handle to the replacement door panel.
e) Fit the replacement panel to the oven inner door.
f ) Re-assemble in reverse order.
SERVICING - WARNING
16 To Remove the Door Latch
a) Remove the oven outer door panel as detailed in Section
15.
b) Remove the fixings that secure the latch assembly to the
inner door panel.
c) Fit the replacement catch and re-assemble in reverse
order.
d) Check correct operation of door.
17 To Remove the Oven Door Seal
a) Open oven door. The seal is held in place by small hooks
on the rear face. At the corner pull seal diagonally away
from the door centre until that hook is released.
b) Proceed to the next hook and release it in a similar way,
and so on. Use force if the hooks are stiff, as the old seal
will be discarded.
c) When fitting new seal, position the seal join at the
bottom. Hook the new seal in one of the corner holes of
the door, and proceed round the door snapping in each
hook in turn.
18 To Adjust the Oven Door Catch Keeper
a) Open the oven door and slacken the locknut at the
keeper base.
b) Adjust the keeper inward or outward as required, until
the desired door operation is obtained.
c) Re-tighten the locknut.
19 To Remove the Hotplate Spark Generator
Disconnect the appliance from the electricity supply.
a) Pull the unit forward to access the cover boxes at the
appliance rear. Remove the fixings that secure the cover
and lift it clear.
b) Undo the terminal connections noting their positions.
c) Undo the fixings that secure the spark generator and
remove the device.
20 To Remove the Hotplate Electrode Leads
Disconnect from the electricity supply.
Pull the unit forward to access the rear of the appliance.
a) Remove the French cooktop, pan supports, hotplate
accessories and burner heads.
b) Remove the hotplate as detailed in Section 1.
c) Remove the cover box and disconnect all HT leads at the
generator.
d) Remove the lower back panel and disconnect the lead at
the electrode.
e) Pull the sleeved bundle of HT leads up through the rear
upright.
27