Falcon 1092 CT Dual Fuel Mode D'emploi page 26

Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
d) Open the grill and RH oven doors. Remove 3 fixings
on the top front and 3 fixings on the control panel
underside.
e) Pull the control panel forward. Remove the connections
from the rear of the three neons. Disconnect the earth
lead and lift the panel clear of the unit.
f ) Replace all parts in reverse order.
g) When replacing any electrical connections refer to the
wiring diagram.
3 To Remove an Outer Side Panel
Disconnect the appliance from the electricity supply.
a) Remove the control panel as detailed in Section 2.
b) Remove the retaining screw on the upper front edge
and the two fixings on the rear or the side panel. Undo
the lower retaining screw situated below the edge at the
panel front corner.
c) Remove the panel by pulling it away from the unit.
Should difficulty be encountered, it may be necessary to
slacken the two closest burners and both brass venturi
as detailed in Section 2.
d) Replace parts in reverse order. Ensure that both venturis
are fully tightened.
4 To Remove an Oven or Grill Neon
Disconnect the appliance from the electricity supply.
a) Remove the control panel as detailed in Section 2.
b) Remove the relevant neon connection and undo the nut
which secures the neon to the control panel.
c) Replace parts in reverse order. Ensure the replacement
neon functions correctly.
5 To Remove a Thermostat
Disconnect the appliance from the electricity supply.
a) Remove the hotplate as detailed in Section 1.
b) Remove the control panel as detailed in Section 2.
c) Open the appropriate oven door and remove the oven
shelves.
d) Pull the unit forward to gain access to the cover box.
Undo the cover screws and lift clear.
RH oven
Remove the two fixings that secure the thermostat phial
cover. Unclip the thermostat phial from the clips in the
oven back panel.
LH oven
Remove the two screws holding the thermostat phial
to the oven fan cover at the rear of the oven. Pull the
unit forward to access the rear of the cooker. Remove
the both cover boxes by removing the fixing screws and
lifting clear. Feed the thermostat capillary clear of the
oven.
e) Disconnect the wires from the thermostat and undo the
two fixings which secure the control to the mounting
plate.
f ) Fit the replacement and re-assemble in reverse order.
Ensure that the phial is clipped to the oven rear,
positioned centrally between the clips. Check that the
thermostat functions correctly.
SERVICING - WARNING
6 To Replace a Grill Controller
Disconnect the appliance from the electricity supply.
a) Remove the hotplate as detailed in Section 1.
b) Remove the control panel as detailed in Section 2.
c) Disconnect the controller wiring. Undo the fixings that
secure the device to the mounting plate.
d) Fit the replacement and re-assemble parts in reverse
order. Check that the replacement functions correctly.
7 To Remove an Oven Cut-Off Thermostat
Disconnect the appliance from the electricity supply.
a) Pull the unit forward to gain access to the cover box.
Undo the cover screws and lift clear.
b) The control is located on the earth plate beside the oven
element connections.
c) Disconnect the thermostat wiring. Undo the fixings that
secure the thermostat to the earth plate and remove.
d) Fit replacement control and re-assemble parts in reverse
order.
8 To Remove a Hotplate Tap
a) Remove the hotplate as detailed in Section 1.
b) Remove the control panel as detailed in Section 2.
c) Unplug the FSD lead from the rear of the tap. Undo
compression fitting at the rear of the tap. Remove the
fixings that secure the tap to the gas rail. Disconnect the
ignition switch wiring.
d) Remove the tap. Remove and discard the gasket seal. Fit
new gasket seal to replacement tap.
e) Re-assemble in reverse order. Check the appliance is gas
sound. Check hotplate ignition.
9 To Change an Ignition Switch
Change the gas tap as detailed in Section 8.
10 To Remove a Hotplate Burner Injector
a) Remove the hotplate as detailed in Section 1.
b) Remove the injector directly from the burner body.
c) Fit the appropriate injector.
d) Re-assemble in reverse order. Check the appliance is gas
sound.
11 To Remove a Hotplate Burner Spark Electrode
a) Remove the French cooktop or pan support, hotplate
accessories and burner head.
b) Undo the hexagonal venturi nut and remove the bezel
from the hotplate. The spark ignition wire will be pulled
through the electrode clearance hole.
c) Disconnect the spark electrode from the ignition wire.
Note
Take care to prevent the ignition wire from falling back
through the clearance hole.
d) Undo the spark electrode from the bezel by removing
the spring clip and spring.
e) Fit the replacement electrode to the burner bezel. Ensure
that the spring and clip are properly located.
f ) Replace in reverse order and check correct burner
ignition.
26