Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Fitting the toothed rack
• To fit the toothed rack to the sliding gate proceed as follows:
- release the geared motor (fig.9), lay the first stretch of the toothed
rack on the pinion and fix it to the gate, then fasten down all the
other parts along the entire length of the gate.
- after having fastened the toothed rack, realign the pinion (play
of 1 to 2 mm between the toothed runner and the pinion) using
the positioning nuts at the base of the geared motor.
This action will prevent the weight of the sliding
gate from damaging the unit when
working.
2 mm
15 mm
6
- Once the unit has been correctly aligned
fasten it down using the lock nuts then
position and fasten down the mechanical
travel limits (opening and closing directions)
mounted on the toothed rack.
• To operate correctly the gate must stop
(closing direction travel limit activated) about 1 cm before it makes
SCALA: 1:2
contact with the mechanical closing direction buffer on the upper
part of the gate (pos. "E" fig.1). As there is a slight deceleration
Drawing number :
DI0409
when the travel limit is activated ("soft stop", the gate moves
Product Code :
SL424EbSb
slightly onward due to inertia), position the mechanical travel limit
Draft :
P.J.Heath
Date :
16-06-2006
according to the entire travel distance.
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
INSTRUCTIONS FOR POSITIONING THE UNIT
7
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
- The geared motor unit has been assembled in the factory to be
fitted to the LEFT SIDE of the gate (internal view).
To install the motor to the RIGHT SIDE of the gate invert the motor
power cables (Red and Black position "CN3" on the electronic
card and the travel limit cables (Red and Blue binding posts "12"
and "13" on the terminal block while the travel limit common wire
(Black position "11") remains in the same position.
28
27
Fuse T1.6A
LC
230V~
line 230V~
trf 230V~
8
OUT CH2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
- Using the "MANUAL MODE" check the correct functioning of
the gate.
OUT CH2
1
2
3
4
5
6
7
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
Description :
Prodotti (plinto 350 mm)
VISTA DI FIANCO CON MOTORE
SCALA: 1:2
Description :
Prodotti Technocity
Drawing number :
DI0073
Nasello finecorsa
Product Code :
SL4024
Draft :
P.J.Heath
Date :
07-07-98
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
ANS400
b1
M1
L1
M1
CN3
CN2
V1 V2
L4
F2
F3
L5
L6
L7
L8
20
8
9
10
11
12
13
14
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
MANUAL RELEASE MECHANISM
Manual release is carried out with the power to the motor inter-
rupted due to a power failure.
To release the gate use the manual release key supplied with the
unit. The key should be kept inside the house in an easily acces-
sible place or stored with the unit itself.
9
To release the unit
Remove the cover "A" using a screwdriver and insert the key "b"
over the T-shaped pin, then rotate the key through 90 degrees in the
direction indicated by the arrow "C" (clockwise). This will release
the clutch and separate the gears from the motor allowing you to
manually manoeuvre the gate by pushing lightly on it.
To relock the unit
Follow the above instructions in reverse order rotating the key
through 90 degrees in the direction indicated by the arrow "D"
SCALA: 1:2
(anticlockwise). Close the release mechanism access cover "A".
Drawing number :
DI0130
Product Code :
SL4024
Never use the manual release mechanism while the gate is in
Draft :
P.J.Heath
Date :
11-06-98
operation.
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Access to the electronic card
To open the cover insert a screwdriver into the slot "G" and turn it
through 90° as shown in fig.9
Caution! Before opening the cover make sure that
the power has been switched off at the mains.
D
D
C H
C H
C
C
C H
C H
B
C H
B
C H
A
C H
A
C H
J2
J1
J1
R1
b1
CHD
CHC
CHb
CHA
J2
MEMO
DEL
P3
P4
L2
1 2
PROG
SEL
D1
P1
P2
L3
15
15
16
17
18
19
20
F
G
9 0 °
A
Description :
Prodotti Technocity
Sblocco motore
b
C
D
Publicité
Table des Matières
