Manual Release Mechanism; Electronic Programmer - Cardin Elettronica SL Série Mode D'emploi

INSTRUCTIONS FOR POSITIONING THE UNIT
7
- The geared motor unit has been assembled in the factory to be fitted
to the LEFT SIDE of the gate (internal view).
To install the motor to the right set the installation parameter (see
page 20).

MANUAL RELEASE MECHANISM

Manual release is carried out with the power to the motor interrupted
due to a power failure. To release the gate use the manual release key
supplied with the unit. The key should be kept inside the house in an
easily accessible place or stored with the unit itself.
8
A
To release the unit
A
the T-shaped pin, then rotate the key through 90 degrees in the direction
C
separate the gears from the motor allowing you to manually manoeuvre
the gate by pushing lightly on it.
To relock the unit
Follow the above instructions in reverse order rotating the key through
Attention! Never use the manual release mechanism while
the gate is in operation.
Moving the gate manually will force the encoder to lose the
position of the gate. To reset the control, once the gate has
been relocked, you will need to give 3 or more movement
commands so that the gate leaf will reach the travel limit
enough times to position itself correctly.
Access to the electronic card
through 90° as shown in fig. 8.
Caution! Before opening the cover make sure that the
power has been switched off at the mains.

ELECTRONIC PROGRAMMER

Electronic control unit for two dc motor with an incorporated encoder
and radio receiver card, which allows the memorisation of 300 user
codes
mitters S449.
The motor rotation speed is electronically controlled, starting slowly and
increasing in speed; the speed is reduced as it nears the travel limit so
as to enable a controlled smooth stop.
Programming is carried out using the buttons P1, P2, P3, and allows you
to set the system, the current sensor and the entire gate travel distance.
The logic carries out position control using an encoder. The intervention
of the anticrush/antidrag sensor during the closing and opening stages
causes travel direction inversion.
F
G
9 0 °
B
C
D
D
A
G
433.92 MHz series trans-
In conformity with the electrical safety standards it is forbid-
den to connect binding posts 9 and 10 directly to a circuit that
receives power greater than 30 Vac/dc.
Warning! For the correct operation of the programmer the
incorporated batteries must be in good condition.
The programmer will lose the position of the gate in case
of blackouts when the batteries are flat the alarm will sound.
Check the good working order of the batteries every six months
(see page 21 "Battery check").
the programmer, release the door (manual release mecha-
nism) and move it manually, checking that it moves smoothly
and has no unusual points of resistance.
at reducing battery power consumption (if installed) during
blackouts; photocells and other safety devices should be
connected to this output.
electronic programmer routes voltage to the CTRL 24 Vdc
output. It then evaluates the state of the safety devices and
if they are at rest it will activate the motor.
allows you to carry out the autotest function (enabled using
that the safety devices are functioning correctly.
dispense with the obligation to install photoelectric cells and
other safety devices foreseen by the safety standards in
force.
B age and frequency rated on the data plate conform to those
of the mains supply.
cable.
contacts must be installed between the unit and the mains
supply.
the ends of cables which are to be inserted into the binding
posts; use cables marked T min 85°C and resistant to atmos-
pheric agents.
both the wire and the insulating sheath are tightly fastened
(a plastic jubilee clip is sufficient).
ELECTRICAL CONNECTION 230 Vac
device wires.
230 Vac mains power
and the through the rubber cable
PS
- connect the live to post 1
- connect the earth to post 5
- connect the neutral to post 2 N
16
IMPORTANT REMARKS
and before powering up
230 Vac power supply only use a 2 x 1.5 mm
230 Vac
TS
N
L
TS
-
2 +
9
L