Nominal Data; Technical Description - Siemens SIMOTICS M-1PH8 Série Instructions De Service / Instruction De Montage

K3G250-RR17-H9
Siemens AG DI MC + LD

3.2 Nominal data

Motor M3G084-DF
Phase 1~
Nominal voltage / VAC 230
Nominal voltage 200 .. 277
range / VAC
Frequency / Hz
50/60
Method of obtaining ml/ce
data
-1
Speed (rpm) / min 3100
Power consumption / W 300
Current draw / A
1.3
Min. ambient -25
temperature / °C
Max. ambient 60
temperature / °C
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Data according to Commission Regulation (EU) 327/
2011
01 Overall efficiency η / %
es
02 Measurement category
03 Efficiency category
04 Efficiency grade N
05 Variable speed drive
06 Year of manufacture
07 Manufacturer
08 Type
09 Power consumption P / kW 0.28
ed
09 Air flow q / m³/h
v
09 Pressure increase total p /
sf
Pa
10 Speed (rpm) n / min -1
11 Specific ratio *
12 Recycling/disposal
13 Maintenance
14 Additional components
*
Specific ratio = 1 + p / 100 000 Pa
fs
Data obtained at optimum efficiency level. The ErP data is determined using a motor-impeller
combination in a standardized measurement setup.
Item no. 55686-5-9970 · ENU · Change 211092 · Approved 2020-05-20 · Page 5 / 12
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
Actual Req. 2015
49.7 44.8
A
Static
65.9 61
Yes
The year of manufacture is specified on the
product's rating label.
ebm-papst Mulfingen GmbH & Co. KG
Amtsgericht (court of registration) Stuttgart
· HRA 590344
D-74673 Mulfingen
K3G250-RR17-H9
805
574
3105
1.01
Information on recycling and disposal is
provided in the operating instructions.
Information on installation, operation and
maintenance is provided in the operating
instructions.
Components used to calculate the energy
efficiency that are not apparent from the
measurement category are detailed in the
CE declaration.

3.4 Technical description

Weight 11.8 kg
Size 250 mm
Motor size
84
Rotor surface Painted black
Electronics housing Die-cast aluminum, painted black
material
Impeller material PA plastic, galvanized sheet-metal plate
Housing material Die-cast aluminum
Support plate material Sheet steel, galvanized
Inlet nozzle material Sheet steel, galvanized
Guard grille material
Steel, phosphated and coated with black
plastic (RAL 9005)
Number of blades 7
Direction of rotation
Clockwise, viewed toward rotor
Degree of protection IP55
Insulation class "F"
Moisture (F) / H1
Environmental (H)
protection class
Installation position Any
Condensation None
drainage holes
Mode S1
Motor bearing Ball bearing
Technical features
- Output 10 VDC, max. 10 mA
- Operation and alarm display
- Alarm relay
- Integrated PID controller
- Power limiter
- Motor current limitation
- PFC, active
- RS-485 MODBUS-RTU
- Soft start
- Control input 0-10 VDC / PWM
- Control interface with SELV potential
safely disconnected from the mains
- Thermal overload protection for
electronics/motor
- Line undervoltage / phase failure
detection
Touch current
<= 3.5 mA
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
Electrical hookup Terminal box
Motor protection Thermal overload protector (TOP)
internally connected
Protection class I (if protective earth is connected by
customer to the housing's connection point)
Conformity with
EN 61800-5-1; CE
standards
Approval CSA C22.2 No. 77 + CAN/CSA-
E60730-1; EAC; UL 1004-7 + 60730-1
Comment Operational is only permitted with the
optional guard grill available from ebm-
papst.
237