Fichier D'exemple Modem_F0.Cfg - Bull ESCALA PL 240T Guide De L'utilisateur

Fichier d'exemple modem_f0.cfg

#
# COMPONENT_NAME: (ESPSETUP) ENTRY SERVICE PROCESSOR SETUP F0
#
# FUNCTIONS: Modem configuration file for many recent Hayes* compatible modems.
# This example uses the AT&F0 reset command to choose the factory defaults.
# This set up is preferred for modems with extended (&) commands.
# vintage modems, setup Z or Z0 is recommended.
# the extended (&) commands and to factory default choices (&Fn), but doesn't
# work properly with this setup file, setup F1 is recommended.
#
# * Trademark of Hayes Microcomputer Products, Inc.
#
# (C) COPYRIGHT International Business Machines Corp. 1996
# All Rights Reserved
# Licensed Materials – Property of IBM
#
# US Government Users Restricted Rights – Use, duplication or
# disclosure restricted by GSA ADP Schedule Contract with IBM Corp.
#
#
# If the modem has configuration switches, they should be set to the
# factory default settings.
ICDelay 1
DefaultTO 10
CallDelay 120
# AT
# &F0
# E0
# V0
# +++
# H0
#
#
#
#
# &C1
# &R1
#
# %N
# %S
#
# Following are common responses from a wide range of modems:
# 16, 15, 12, 10, 5 and 1 are connection responses.
# 7=busy; 6=no dial tone; 4=error; 3=no carrier; 2=ring; 0=OK
#
# PROGRAMMING NOTE: No blanks between double quote marks (").
condout:
connect:
expect "16\r" or "15\r" or "14\r" or "12\r" or "10\r" or "5\r" or "1\r" busy
"7\r"
timeout 60
retry:
expect "16\r" or "15\r" or "14\r" or "12\r" or "10\r" or "5\r" or "1\r" busy
"7\r"
timeout 60
Attention Code
Reset. Restore profile 0 Q0
Turn echo off
Use numeric responses
Escape to command mode
Hang–up
Detect CD
Ignore RTS (CTS)
Call–Out phone number
Modem speed (available to users)
send "AT&F0Q0T\r"
ignore "0\r" or "OK\r\n" timeout 2
send "ATE0T\r"
expect "0\r" or "OK\r\n" timeout 2
send "ATQ0V0X0T\r"
expect "0\r" timeout 2
send "ATS0=0\r"
expect "0\r" timeout 2
send "AT&C1&D2&R1\r"
expect "0\r" timeout 2
done
send "ATDT%N\r"
done
send "A/"
done
If your modem responds to
, Inserts delay in dialing commands
Turn on responses
Q1 Turn off responses
S0=0 Automatic answer inhibit
S0=2 Answer on second ring
X0=0 Limit modem response codes
T = Tone mode. When used as T\r, it is a
no op to maintain program synchronization
when modem may/will echo the commands.
&D2 Respond to DTR (often the default)
%P Paging phone number
Add others as required.
# Reset modem. Select profile 0
# Ignore modem response.
# Initialize modem: Echo OFF,
# Enable responses (Numeric),
# Limit response codes.
# Confirm commands successful.
# Set AutoAnswer OFF
# Confirm command successful.
# Detect carrier and DTR,
# Ignore RTS.
# Confirm command successful.
# Tone dialing command.
# %N from Call Home setup.
# Expect a connection response.
# Repeat the previous command.
# Expect a connection response.
Configurations de modems
For early
C-17