Stiga SBC 627 K Manuel D'utilisation page 113

not to impair the safety and efficiency of the
machine. If in doubt, contact your dealer.
WARNING! Unpacking and completing
the assembly should be done on a flat and
stable surface, with enough space for moving
the machine and its packaging, always mak-
ing use of suitable equipment.
Disposal of the packaging should be done in ac-
cordance with the local regulations in force.
1.1 COMPLETING THE MACHINE
1.1a. Models SBC 627 K – 635 K – 645 K
653 K (Fig. 1)
– Slide the contoured plate (1) until it is close to
the holes in the drive tube (2).
– Fit the top part (3) of the front handgrip on the
plate (1) so that the pin (4) fits into one of the
three holes provided on the drive tube (2) to
adjust the handgrip to the operator's prefer-
ence.
– J oin the bottom part (5) with the guard and at-
tach it to the top part (3), tightening the screw
(6) completely.
1.1b Models SBC 627 KD – 635 KD – 643 KD
(Fig. 2)
– U nscrew the middle knob (1) and remove the
cap (2).
– I nsert the handle bar (3), making sure that the
controls are on the right.
– S et the handle bar in the most comfortable
working position and lock it using the cap (2)
and knob (1).
– Fasten the casing (4) of the controls to its ca-
ble fastener (5).
NOTE Loosening the knob (1) the handle bar can
be rotated to reduce its bulk for storage.
1.1c Models SBC 645 KD – 653 KD (Fig. 3)
– L ift the lever (1) and remove it loosening the
screw (2).
– R emove the cap (3) from the support (4).
– Put the handle bar (5) into the seat in the sup-
port (4), making sure that the controls are on
the right.
– F it the cap (3) and lever (1), without tightening
the screw (2).
– L ower the lever (1) and check that the handle
bar (5) is firmly locked; if not, tighten the screw
(2) until it is satisfactorily locked.
– Fasten the casing (6) of the controls to its ca-
ble fastener (7).
NOTE Lifting the lever (1) the handle bar can be
moved to the position most comfortable for the
operator.
1.1d Models SBC 645 KF – 653 KF (Fig. 4)
– Slide the contoured plate (1) until it is close to
the holes in the drive tube (2).
– Fit the top part (3) of the front handgrip on the
plate (1) so that the pin (4) fits into one of the
three holes provided on the drive tube (2) to
adjust the handgrip to the operator's prefer-
ence.
– Join the bottom part (5) with the guard and at-
tach it to the top part (3), tightening the screw
(6) completely.
– Remove the protective cuffs (11) from both
ends of the flexible drive tube (12), taking note
that there are differences between them.
– Lift the pin (13), turning it so that it remains
lifted and insert the end with the hole (12a) in
the seat of the power unit, ensuring that the
hole is turned upward.
– Release the pin (13), making sure it is lowered
completely to lock the end of the tube (12a).
– Insert the end with the groove (12b) in the
protruding hub of the front handgrip (14) and
fasten it with the screw (15) ensuring it stays
locked.
– Insert the register (17) of the throttle wire in
the support slot and connect the wire (18) to
the carburettor lever (19); then work the nuts
(20) to tighten the wire and block the register
on the support.
– Connect the two terminals of the cables (21)
and (22) to the corresponding cables on the
power unit.
1.2 FITTING THE GUARD ON THE CUTTING
DEVICE (Fig. 5)
WARNING!
vided with a specific guard. Never use guards
other than those indicated for each cutting
device.
WARNING!
fit the blade guard.
– R emove the screw (1) from the guard (2).
– Insert the tab (3) in the guard seat (2) and fas-
ten the guard with the screw (1).
1.3 FITTING AND REMOVING CUTTING
DEVICES AND PREPARING GUARDS
WARNING!
ting devices or ones homologated by the
Manufacturer.
14
Each cutting device is pro-
Wear protective gloves and
Use only original cut-