Erreka VIVO-M203 Manuel De L'installateur page 78

INSTALLATION
Operator connections for sliding gates and up-and-over doors
(parameters C302 and C303)
ST1: open
ST2: close
A1
E1
P13 P14 P15 P16
A1
E1
P13 P14 P15 P16
ENCODER 1
E1
P13 P14 P15 P16
ENCODER 1
Operator connection
Single encoder
connection (C701)
Connector E1:
V+: red wire
GND: white wire
SGN1: green
or blue wire
SGN2: do not connect SGN2: close (FCC)

In sliding gates (C302) and up-and-over doors (C303) it is only possible to use a single motor
(M1), which should be connected to the "MOTOR 1" cable connectors.
When using a single encoder (C701, C704) or dual encoder (C703), always connect it to the
"ENCODER 1" cable connectors.
When using limit switches (C702, C704 or C705), always connect to the "ENCODER 2" cable
connectors.
74
Installation Guide
P24 P25
ST2
ST1
P17 P18 P19 P20
P13 P14 P15 P16
ENCODER1 ENCODER2
P1 P2 P3 P4 P5 P6 P7 P8 P9 P10
P1 P2 P3 P4 P5 P6 P7 P8 P9 P10
C701
E2 E1
P13 P14 P15 P16
ENCODER 1 ENCODER 2
C703
E2
E1
P13 P14 P15 P16
ENCODER 2
C705
A1
ATS NA
E2
P13 P14 P15 P16
ENCODER 2
Limit switches
connection (C702)
Connector E2:
V+: do not connect V+:
GND: common (COM) GND: white wire
SGN1: opening (FCA) SGN1: green
P21 P22 P23
-FT
AUX
(Test)
24 Vdc
P11 P12
P11 P12 G7 G8 G9 G10
G4
MOTOR2
C702
A1
E2
P13 P14 P15 P16 P13 P14 P15 P16
ENCODER 1 ENCODER 2
C704
A1 A1
E2
P13 P14 P15 P16 P13 P14 P15 P16
ENCODER 1 ENCODER 2
ATLAS Connection (ATS) G6xxI (C705)
Connector E2:
V+: do not connect
GND: common (COM)
SGN1: ATS operator safety micro and NA
closing micro (parallel connection)
SGN2: bridge with GND
Dual encoder
connection (C703)
Connector E1: Connector E1:
red wire V+:
GND: white wire
SGN1: green
or blue wire
SGN2: purple wire SGN2: do not connect SGN2: close (FCC)
CN13
G5 G6 G1 G2 G3 N L
N L
POWER - 230V
POWER - 230V
MOTOR1
A1
M o t o r
connection
G1/G4: open
G2/G5: close
G3/G6: common
A1: operator 1
E1: "ENCODER 1" cable connectors
E2: "ENCODER 2" cable connectors
FC and single encoder connection
(C704)
Connector E2:
red wire V+: do not connect
GND: common (COM)
SGN1: opening (FCA)
or blue wire
VIVO-M203:
230V, 50Hz
VIVO-M203M:
125V, 60Hz
P239Z4