Description Of Transition Sleeve; Ums75-90/102-125 For Connecting Smooth; Ducts Dn75; Installation - Hauff-Technik ESH Instructions De Montage

Pipe connections for ESH/MSH-PolySafe/MSH-FW/ESH/
MSH-FUBO
12

Description of transition sleeve

UMS75-90/102-125 for connecting
smooth cable ducts or Hatefl ex
spiral hoses Øa = 102-125 mm and
Hatefl ex spiral hoses 14070 and
14078, and also corrugated cable

ducts DN75

Legend for Fig. 24
1 Hatefl ex hose 14078
2 Stainless steel clamp
3 Transition sleeve UMS75-90/102-125
4 Smooth cable duct
13

Installation

Variant 1
Connection of transition sleeve to smooth
cable duct Ø a 125 mm.
Tighten clamping strap to 3 Nm (see Fig.: 25).
Variant 2
Connection of transition sleeve to smooth
cable duct Ø a 110 mm with adapter ring.
Prior to mounting the smooth cable duct Ø a 110
mm, release the mounted clamping strap and insert
the adapter ring in the transition sleeve.
Then insert the smooth cable duct Ø a 110 mm up
to the stop in the transition sleeve UMS and tighten
the clamping strap to 3 Nm (see Fig. 26).
Variant 3
Connection of transition sleeve to Hatefl ex
spiral hose 14110.
Prior to mounting the Hatefl ex spiral hose 14110,
release the mounted clamping strap and insert the
adapter ring in the transition sleeve.
Then insert the Hatefl ex spiral hose 14110 up to the
stop in the transition sleeve UMS and tighten the
clamping strap to 3 Nm (see Fig. 27).
Variant 4
Connection of transition sleeve to Hatefl ex
spiral hose 14078 (see Fig. 28).
Tighten clamping strap to 1.5 Nm.
Variant 5
Connection of transition sleeve to corrugated
cable duct DN75 (see Fig. 29).
Prior to mounting the corrugated cable duct,
release the mounted clamping strap and reverse
the outer rubber lip of the transition sleeve UMS
towards the inside, if necessary moistening with a
little water (see Fig. 30). Then insert the corrugated
cable duct DN75 up to the stop in the transition
sleeve UMS and tighten the clamping strap to 1.5
Nm (see Fig. 31).
16
14
Legend for Fig. 32
1
2
3
4
15
1
2
Service telephone +49 7322 1333-0
Art. Nr.: 5090033071 Rev.: 01/2020-01-21
• Cable ducts or Hatefl ex spiral hoses in the
insertion area must be clean, grease-free and
cut off at right angles.
• In the case of thin-walled or foamed corruga-
ted pipes, only tighten the clamping straps to
a point at which the pipes are not deformed.
• In the case of corrugated cable ducts Øa = 90
mm, suitable ring clips (available from Hauff-
Technik) must be used for better stabilisation.
Pipe/hose type
Smooth cable duct
Corrugated cable duct
Hatefl ex spiral hose 14078
Hatefl ex spiral hose 14110
Description of branch sleeve
AMS3x75 for connecting smooth
cable ducts Øa = 75 mm and corruga-
ted cable ducts DN75
Sleeve pipe MSH/ESH
Stainless steel clamp
Branch sleeve AMS3x75
Corrugated cable duct DN75
Installation
Release the mounted clamping straps and insert
smooth or corrugated cable ducts up to the stop in
the branch sleeve AMS (see Fig. 33).
The tighten the clamping strap to max. 4 Nm in the
case of smooth cable ducts and max. 1.5 Nm in the
case of corrugated cable ducts.
Cable ducts and branch sleeves must be clean
and grease-free in the area of insertion.
Completed branch sleeve AMS with smooth and
corrugated cable ducts DN75 (see Fig. 34).
The branches of the sleeve must not be under
mechanical stress during or after mounting of
the cable ducts.
EN
Tightening
torque
3 Nm
1.5 Nm
1.5 Nm
3 Nm
Subject to alterations.