Preparing Spray Solution; Spraying; Safety; Maintenance And Care - Solo 425 Instructions D'emploi

8. PREPARING SPRAY SOLUTION

- Prepare solution outside, never within living areas, stables
or in storage area for foodstuff.
- Prepare solution with powder chemicals in a separate
container. Mix well and then transfer to sprayer tank.
- Note: If necessary, the solution can be re-agitated in the
tank by stirring with the spray tube.
- With liquid plant protection chemicals (if full tank is
required), fill sprayer tank 1/4 full with water, add pre-
diluted chemical and then add remaining water as required.
- When applying organic spray solutions please filter the
solution as or before pouring into the spray tank.
Always observe the Safety Notes provided by
the chemical manufacturer
9. FILLING
- When filling the spray tank always use the filter provided
with the machine and observe the total filling process.
- Avoid a direct connection between water hose and spray tank.
- Spray Chemical may not reach the water mains.
- When filling ensure that no spray chemicals will
contaminate the environment or water mains network.
- Avoid any overflow from the tank and any contamination
of public waterways, drainage and water channels.

10. SPRAYING

- Prime the pump with a few up and down strokes of the
pump lever.
- By squeezing the shut-off trigger valve, liquid will be
forced through the spray nozzle.
- When the shut-off trigger valve is released, the spray will
stop.
- Always release all pressure in the tank or spray line before
commencing service or maintenance work on the machine.
- When removing the spray tube from the machine always
point the end of the tube away from yourself.
- For safety reasons, the sprayer should not be used for the
application of aggressive liquids (sanitizers, desinfectants
and preservatives) liquids above 40 °C temperature
flammable liquids with a flashpoint below 55 °C

11. SAFETY

- Do not operate the sprayer while persons (especially
children) or animals are in close vicinity. The operator is
responsible for any damage or harm to third parties.
- When using plant protection equipment and while
working with plant protection chemicals of any kind, always
observe the Safety Precautions prescribed by the chemical
manufacturer. The operator is to observe Personal Safety
Regulations (Safety Clothing).
-Heavily dilute (approx. 1:10) surplus spray fluid left over
after treatment of field or garden, and spray the solution
over the area you have already treated.
- After every use and especially after the end of the spraying
season, clean and flush the sprayer, tank as well as all parts
which come in contact with chemicals.
- Residues of plant protection chemicals may lead to
corrosion and damage of the sprayer.
- Clean and service wear parts such as nozzles, filters,
gaskets and seals.
- Never clean nozzles with hard objects.
- Any remaining excess spray solution can be heavily diluted
(approx. 1:10 ratio) and applied over the already treated area.
- Damaged parts should be replaced without delay. Always
use Original Parts.
Medium Volume Guide for Plant Protection
Ground Plants
Small Shrubs
Espalier trees, pencil bushes 0.5 - 1.0 ltr. per plant
Taller bush trees 2.0 ltr. per plant
Older, free standing trees 3.0 - 5.0 ltr. per tree

12. MAINTENANCE AND CARE

- The SOLO Backpack Sprayer is almost maintenance free. If
the tank lid becomes hard to tighten or open, apply all to
the lid gasket.
- Proper Maintenance also includes:
- Regular check of the spray tank
- Regular check of spray line and screw connectors
- Clean all filters and check for any damage
- To protect piston, cylinder and piston collar (models 425/
435/ 473P) from impurities in the spray solution, an
additional filter is fitted on the inlet side of the pressure
tank. This filter can be cleaned by vigorously shaking the
tank when flushing it.
With models 425/435/473P:
- After disassembly of pump components or after replacing
the piston collar, use water resistant grease to lubricate the
piston and the collar.
- In case of unexpected problems please refer to your SOLO
Dealer.

13. STORAGE

Even through the tank is manufactured from UV-stabilized
material we recommend that the unit is protected from
direct sunlight and stored in a dry room, away from children
and animals.
In areas subject to frost, always drain all the liquid from
tank, pressure tank and hoses.
Please always use SOLO Original Replacement Parts available
from your SOLO Partner.
0.3 - 0.5 ltr. for 10 m 2
1.0 - 1.5 ltr. for 10 m 2