Operation; Set Up Scenes (Accessed From Tabletop/Wall Control, Single Zone) - Lutron Radio Touch RTA-RS232 Guide D'installation Et De Mise En Service

Operation

Set Up Scenes
(accessed from
Tabletop/Wall Control, single zone type)
It is very easy to generate scenes composed of
zones of lights. These scenes can be easily
accessed and modified from tabletop or wall
controls.
Example:
A room has the following lighting zones addressed to
the RTA-RS232 interface:
Zone Description Level for New Scene
0 Front lights 25%
1 Rear lights 80%
2 Wall washers 50%
Select an unused lighting zone on the RTA-RS232
to contain the scene. This zone should have no
controllers addressed to it that are not part of the
scene.
To configure the zone, enter configuration mode, and
set the zone type (in this example, zone 9 will be
configured to Lights).
Note: Feedback from the RTA-RS232 (prefixed with
a tilde/~) will occur only if the RTA-RS232 has Reply
Back Mode turned ON.
Enter Configuration Mode:
Host sends :CON,ENTER<CR>
RS232 replies ~CON,RPT,ENTER
Configure Zone as Lights:
Host sends :CON,TYPE,9,L<CR>
RS232 replies ~CON,RPT,TYPE,9,L
To add the target zone to the RF controllers, place
each controller in the scene in Program Mode by
pressing its programming button. See the
RadioTouch Installer's Guide for information on
addressing. Each controller can be addressed to the
target zone at the same time.
R adio T ouch
120/277 V 60 Hz
TM
RT A-RX-F 16 A Max.
LISTED 243C
®
I nd . C ont . E q .
Coopersburg, PA 18036 USA
Refer to the Installers Guide for more
detailed instructions.
Consulte la Guía de Instaladores para
USA, Canada 1-800-523-9466
información más detallada.
Mexico 1-888-235-2910
Référer au Guide d'installation pour plus de
www.lutron.com
renseignements détaillés.
CONFIGURACIONES
REGLAGES
SETTINGS PWR STAT PROG 100 H r /100%
ON
1 2 3 4 5
1 2
3 4 5 6 7 8
0-10
V
®
ON
1 2 3 4 5
1 2 3 4 5 6 7 8
R
RadioTouch controller
PROG button
RadioTouch
Issue the ADD Command:
Host sends :CON,ADD,9<CR>
RS232 replies ~OK
Exit Configuration Mode:
Host sends :CON,EXIT<CR>
RS232 replies ~CON,RPT,EXIT
Take each controller out of Program Mode by
pressing its programming button.
Verify that the controllers have been addressed to
zone 9 by turning zone 9 OFF, then ON.
Host sends :XC,9,OFF<CR>
RS232 replies ~OK
The lights should go OFF for all intended zones.
Host sends :XC,9,100<CR>
RS232 replies ~OK
The lights should go ON for all intended zones.
To adjust the lights to the desired levels for the new
scene, enter Preset Adjust mode. Either use the PSA
command, or put DIP switch 1 on each controller in
the down position.
R adio T ouch
120/277 V 60 Hz
TM
16 A Max.
RT A-RX-F
LISTED 243C
®
I nd . C ont . E q .
Coopersburg, PA 18036 USA
Refer to the Installers Guide for more
detailed instructions.
Consulte la Guía de Instaladores para
USA, Canada 1-800-523-9466
información más detallada.
Mexico 1-888-235-2910
Référer au Guide d'installation pour plus de
www.lutron.com
renseignements détaillés.
CONFIGURACIONES
REGLAGES
SETTINGS PWR STAT PROG 100 H r /100%
ON
1 2 3 4 5
1 2 3 4 5 6 7 8
0-10
® V
ON
1 2 3 4 5
1 2 3 4 5 6 7 8
Enter Preset or Adjust Mode:
Host sends :PSA,9,ENTER<CR>
RS232 replies ~OK
Adjust each zone to the desired level either by
issuing explicit commands, or by using
RAISE/LOWER. Presets cannot be used to adjust
the light intensity.
Explicit Level Command for Each Zone:
Host sends :XC,0,25<CR>
RS232 replies ~OK
Host sends :XC,1,80<CR>
RS232 replies ~OK
Host sends :XC,2,50<CR>
RS232 replies ~OK
RTA-RS232 Programming and Operation Guide
TM
RadioTouch controller
Set DIP switch 1 to
down position
23