Midi Implementation; Transmitted Data - Roland V Accordion FR-7 Mode D'emploi

FR-7/FR-5 V-Accordion
MIDI implementation | Demo Songs

12. MIDI implementation

1. Received data
I Channel Voice Messages
G Note off
Status 2nd byte
8nH kkH
n = MIDI channel number:
kk = note number:
vv = note off velocity:
G Note on
Status 2nd byte
9nH kkH
n = MIDI channel number:
kk = note number:
vv = note on velocity:
G Control Change
• The value specified by a Control Change message is not reset by a Program
Change, etc.
❍ Bank Select (Controller number 0, 32)
Status 2nd byte
BnH 00H
BnH 20H
n = MIDI channel number:
mm = Bank number MSB:
ll = Bank number LSB:
• Only for Free Bass.
❍ Expression (Controller number 11)
Status 2nd byte
BnH 0BH
n = MIDI channel number:
vv = Expression:
• This adjusts the volume of a Part. It can be used independently from Volume
(CC07) messages. Expression messages are used for musical expression within
a performance, e.g., expression pedal movements, crescendo and decrescendo.
❍ Hold 1 (Controller number 64)
Status 2nd byte
BnH 40H
n = MIDI channel number:
vv = Control value:
❍ Program Change
Status 2nd byte
CnH ppH
n = MIDI channel number:
pp = Program number:
❍ Channel Pressure
Status 2nd byte
DnH vvH
n = MIDI channel number:
vv = Channel Pressure:
I System Realtime Messages
❍ Active Sensing
Status
FEH
• When Active Sensing is received, the FR-7/FR-5 starts monitoring the intervals of
all further messages. While monitoring, if the interval between messages exceeds
420 ms, the same processing will be carried out as when All Sounds Off, All Notes
Off and Reset All Controllers are received, and message interval monitoring will
be halted.
❍ Start
Status
FAH
• When an FA message is received from an external MIDI device such as sequenc-
er, the FR-7/FR-5 sends all necessary MIDI information for a song header setup:
Treble, Orchestra, Bass/Free, Orchestra Bass, sound setup.
178
3rd byte
vvH
0H~FH (Ch.1~16)
00H~7FH (0~127)
00H~7FH (0~127)
3rd byte
vvH
0H~FH (Ch.1~16)
00H~7FH (0~127)
01H~7FH (1~127)
3rd byte
mmH
llH
0H~FH (Ch.1~16)
00H~7FH
00H~7FH
3rd byte
vvH
0H~FH (Ch.1~16)
00H~7FH (0~127)
3rd byte
vvH
0H~FH (Ch.1~16)
00H~7FH (0~127)
00H~63H= Off/64H~7FH= On
0H~FH (Ch.1~16)
00H~0DH: Treble Register 1~14
00H~15H: Orchestra Register 1~22
00H~06H: Bass/FreeBass/Orch.Bass
Register 1~7
00H~27H: Set 1~40
0H~FH (Ch.1~16)
00H~7FH (0~127)
I System Exclusive Messages
Status Data byte Status
F0H iiH, ddH, ......,eeH F7H
F0H: System Exclusive Message status
ii = ID number: An ID number (manufacturer ID) to indicate the manufacturer
whose Exclusive message this is. Roland's manufacturer ID is
41H.
dd,...,ee = data: 00H~7FH (0~127)
F7H: EOX (End Of Exclusive)
The System Exclusive Messages received by the FR-7/FR-5 are messages related
to Data Set (DT).
G Data Set 1 DT1 (12H)
Status Data byte
F0H 41H, dev, 42H, 12H, aaH, bbH, ccH, ddH, ... eeH,
ffH, sum
Byte Explanation
F0H Exclusive status
41H ID number (Roland)
10H Device ID
00H Model ID #1 (FR-7/FR-5 V-Accordion)
7CH Model ID #2 (FR-7/FR-5 V-Accordion)
12H Command ID (DT1)
aaH Address MSB: upper byte of the starting address of
the data to be sent
bbH Address: upper middle byte of the starting address of
the data to be sent
ccH Address: lower middle byte of the starting address of
the data to be sent
ddH Address LSB: lower byte of the starting address of
the data to be sent
eeH Data: the actual data to be sent. Multiple bytes of data
are transmitted in order starting from the address.
:: ::
ffH Data
sum Checksum
F7H EOX (End of Exclusive)
• The amount of data that can be received at one time depends on the type of data,
and data will be transmitted from the specified starting address and size.
• Data larger than 256 bytes must be divided into packets of 256 bytes or less, and
each packet must be sent at an interval of about 20ms.

2. Transmitted data

I Channel Voice Messages
G Note off
Status 2nd byte 3rd byte
8nH kkH vvH
n = MIDI channel number: 0H~FH (Ch.1~16)
kk = note number: 00H~7FH (0~127)
vv = note off velocity: 00H~7FH (0~127)
G Note on
Status 2nd byte 3rd byte
9nH kkH vvH
n = MIDI channel number: 0H~FH (Ch.1~16)
kk = note number: 00H~7FH (0~127)
vv = note on velocity: 01H~7FH (1~127)
G Control Change
❍ Bank Select (Controller number 0, 32)
Status 2nd byte 3rd byte
BnH 00H mmH
BnH 20H llH
n = MIDI channel number: 0H~FH (Ch.1~16)
mm = Bank number MSB: 00H~7FH
ll = Bank number LSB: 00H~7FH
❍ Volume (Controller number 7)
Status 2nd byte 3rd byte
BnH 07H vvH
n = MIDI channel number: 0H~FH (Ch.1~16)
vv = Volume: 00H~7FH (0~127), Initial value = 64H (100)
• Volume messages are used to adjust the volume balance of each Part.
Status
F7H