Warranty; Advice On Lighting A Fire - Nordpeis Casa Manuel D'installation

If different detergents are used they may damage the
glass. A good advice for cleaning the glass is to use a
damp cloth or kitchen roll paper and apply some ash
from the burn chamber. Rub around the ash on the
glass and finish off with a piece of clean and damp
kitchen roll paper. NB! Only clean when the glass is
cold.
Check regularly that the transition between the glass
and the door is completely tight. Possibly tighten the
screws that hold the glass in place - but not too hard,
as this can cause the glass to crack. Periodically,
it may be necessary to change the gaskets on the
door to ensure that the burn chamber is air tight and
working optimally. These gaskets can be bought as a
set including ceramic glue.
REFRACTORY
GLASS CANNOT
BE RECYCLED
Refractory glass should
be disposed of as resid-
ual waste, together with
pottery and porcelain
Recycling of the refractory glass
Refractory glass cannot be recycled. Old glass, bre-
akage or otherwise unusable refractory glass, must be
discarded as residual waste. Refractory glass has a
higher melting temperature, and can therefore not be
recycled together with glass. In case it would be mixed
with ordinary glass, it would damage the raw material
and could, in worst case end the recycling of glass.
It is an important contribution to the environment to
ensure that refractory glass does not end up with the
recycling of ordinary glass.
Packaging Recycle
The packaging accompanying the product should be
recycled according to national regulations.

7. Warranty

For detailed description of the warranty
conditions see the enclosed warranty card or visit
our website www.nordpeis.com
The stoves have a plaque with the RRF number
40 09 1919. The CE mark is situated under the stove.

8. Advice on Lighting a Fire

The best way to light a fire is with the use of lightening
briquettes and dry kindling wood. Newspapers
cause a lot of ashes and the ink is damaging for the
environment. Advertising flyers, magazines, milk
cartons and similar are not suitable for lighting a fire.
Good air supply is important at ignition. When the flue
is hot the draught increases and door can be closed.
Warning: NEVER use a lighting fuel such as
petrol, paraffin, methylated spirits or similar
for lighting a fire. This could cause injury to
you as well as damaging the product.
Use clean and dry wood with a maximum moisture
content of 20% and minimum 16%. The wood logs
should dry for a minimum of 6 months after it is cut.
Humid wood requires a lot of air for the combustion,
as extra energy/heat is required for drying the humid
wood and heat effect is therefore minimal. In addition
this creates soot in the chimney with the risk of
creosote and chimney fire.
Storing of Wood
In order to ensure that the wood is dry, the tree should
be cut in winter and then stored during the summer,
under roof and in a location with adequate ventilation.
The wood pile must never be covered by a tarpaulin
which is lying against the ground as the tarpaulin will
then act as a sealed lid that will prevent the wood from
drying. Always keep a small amount of wood indoors
for a few days before use so that moisture in the
surface of the wood can evaporate.
Firing
Not enough air to the combustion may cause the glass
to soot. Hence, supply the fire with air just after the
wood is added, so that the flames and gases in the
combustion chamber are properly burnt off. Open the
air vent and have the door slightly ajar in order for the
flames to establish properly on the wood.
Note that the air supply for the combustion also can
be too large and cause an uncontrollable fire that
very quickly heat up the whole hearth to an extremely
high temperature (when firing with a closed or nearly
closed door). For this reason you should never fill the
combustion chamber completely with wood.
It is recommended to keep an even fire with a small
amount of wood. If too many logs are put on the
hot ember, the air supply will not be sufficient for
reaching the require temperature, and the gases will
be released unburnt. For this reason it is important
to increase the air supply just after adding the logs in
order to have proper flames in the burn chamber so
that the gases are burnt.
Choice of Fuel
All types of wood, such as birch, beech, oak, elm,
English 19