Publicité
ENGLISH
Charger LED Modes
SC125, SC200 SC400, SC401
Charging:
Green LED Intermittent
Fully Charged:
Green LED Solid
Hot/Cold Pack Delay:
Green LED Intermittent
Red LED Solid
● Plug the charger (9) into an appropriate outlet before
inserting battery pack (6).
● The green charging light (9a) will blink continuously
indicating that the charging process has started.
● The completion of charge will be indicated by the green
charging light (9a) remaining ON continuously. The battery
pack (6) is fully charged and may be removed and used at
this time or left in the charger (9).
● Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Note: The compatible charger(s) will not charge a faulty
battery pack. The charger will indicate a faulty battery pack by
refusing to light.
Note: This could also mean a problem with a charger. If the
charger indicates a problem, take the charger and battery
pack to be tested at an authorized service centre.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
Hot/Cold Pack Delay
When the charger detects a battery that is too hot or too
cold, it automatically starts a Hot/Cold Pack Delay, the green
LED (9a) will flash intermittently, while the red LED (9b) will
remain on continuously, suspending charging until the battery
has reached an appropriate temperature. The charger then
automatically switches to the pack charging mode. This
feature ensures maximum battery life.
SC120
Charging:
Green LED
Intermittent
8
(Original instructions)
Fully Charged:
Green LED
Solid
Hot/Cold Pack
Delay:
Green LED
Intermittent
Red LED Solid
Plug the charger (9) into an appropriate outlet.
u
Insert and fully seat battery pack (6). Green charging
u
light(s) (9a) will continuously blink while charging.
Charging is complete when the green charging light(s)
u
(9a) remain(s) continuously ON. Battery pack can be left
in charger or removed.
Warning! Charger will not charge a faulty battery pack, which
may be indicated by the charging light(s) staying OFF. Take
charger and battery pack to an authorized service center if
light(s) stay(s) OFF.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
Hot/Cold Pack Delay
When the charger detects a battery pack that is too hot or too
cold, it automatically starts a Hot/Cold Pack Delay, suspending
charging until the battery pack has reached an appropriate
temperature. The charger then automatically switches to the
pack charging mode. This feature ensures maximum battery
pack life.
A cold battery pack may charge at a slower rate than a warm
battery pack.
The hot/cold pack delay will be indicated by the green light(s)
(9a) continuing to blink and with the red light (9b) continuously
ON or blinking. Once the battery pack has reached an
appropriate temperature, the red light will turn OFF and the
charger will resume the charging process.
Wall Mounting
Some STANLEY FATMAX chargers are designed to be wall
mountable or to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an electrical
outlet, and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
separately) at least 1"(25.4 mm) long, with a screw head
diameter of 0.28-0.35"(7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32"(5.5 mm) of the
screw exposed. Align the slots on the back of the charger with
Publicité
