Publicité
ENGLISH
achieved, increase the collar setting and continue
tightening the screw.
Repeat until you reach the correct setting.
u
Use this setting for the remaining screws.
u
Dual range switch (Fig J)
The dual range feature of your drill allows you to shift gears
for greater versatility.
● To select low speed, high torque setting (position1),
turn tool off and permit to stop. Slide gear shifter button (4)
away from the chuck.
● To select the high speed, low torque setting (position 2),
turn tool off and permit to stop. Slide gear shifter button
back toward the chuck.
Note: Do not change gears when tool is running. If you are
having trouble changing gears, make sure that the dual range
gear button is either completely pushed forward or completely
pushed back.
Screw driving
● For driving fasteners, the forward/reverse button should
be pushed to the left.
● Use reverse (button pushed to the right) for removing
fasteners.
Note: When moving from forward to reverse, or vice versa,
always release the trigger switch first.
Drilling
● Use sharp drill bits only.
● Support and secure work properly, as instructed in the
Safety Instructions.
● Use appropriate and required safety equipment, as
instructed in the Safety Instructions.
● Secure and maintain work area, as instructed in the Safety
Instructions.
● Run the drill very slowly, using light pressure, until the hole
is started enough to keep the drill bit from slipping out of it.
● Apply pressure in a straight line with the bit. Use enough
pressure to keep the bit biting but not so much as to stall
the motor or deflect the bit.
● Hold the drill firmly with two hands, one hand on the
handle, and the other gripping the bottom around the
battery area or the auxiliary handle if provided.
● DO NOT CLICK THE TRIGGER OF A STALLED DRILL
OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE
TO THE DRILL CAN RESULT.
● Minimize stalling on breakthrough by reducing pressure
and slowly drilling through the last part of the hole.
● Keep the motor running while pulling the bit out of a drilled
hole. This will help reduce jamming.
● Make sure switch turns drill on and off.
Drilling in wood
Holes in wood can be made with the same twist drill bits used
for metal or with spade bits. These bits should be sharp and
10
(Original instructions)
should be pulled out frequently when drilling to clear chips
from the flutes.
Drilling in metal
Use a cutting lubricant when drilling metals.
The exceptions are cast iron and brass which should be drilled
dry. The cutting lubricants that work best are sulphurized
cutting oil.
LED work light (Fig H)
When drill is activated by pulling the trigger switch (1), the
integrated LED work light (8) will automatically illuminate the
work area.
Note: The work light is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Troubleshooting
Problem
Possible cause
Unit will not start.
Battery pack not
installed properly.
Battery pack not charged.
Unit starts
The switch has been left in
immediately
the "on" position.
upon inserting
battery
Battery pack will
Battery pack not inserted
not charge.
into charger.
Charger not plugged in.
Surrounding air
temperature too hot or
too cold.
Unit shuts off
Battery pack has reached
abruptly.
its maximum thermal limit.
Out of charge. (To
maximize the life of the
battery pack it is designed
to shutoff abruptly when
the charge is depleted
Maintenance
Your STANLEY FATMAX tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
@
regular cleaning.
Warning! Before performing any maintenance on
the tool, remove the battery from the tool. Unplug the
charger before cleaning it.
● Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
● Regularly clean the motor housing using a damp cloth.
● Do not use any abrasive or solvent-based cleaner.
Possible solution
Check battery pack
installation.
Check battery pack
charging requirements
The switch must be
moved to "off" to prevent
the tool from immediately
starting when battery
is inserted.
Insert battery pack into
charger until LED lights.
Plug charger into a working
outlet.
Move charger and battery
pack to a surrounding
air temperature of above
45º C or below +40.5º C.
Allow battery pack to cool
down.
Place on charger
and allow to charge.
Publicité
